Jump to content
SAU Community

Recommended Posts

Hey guys, I saw this boost controller on the Hikari website and a few others, yet i havent found any other info on them in regards to how they preform compared to the way more expensive Jap brands. FYI Hikari are sellin them for 320. Thats a fully electronic Dual stage boost controller that has in cabin control. Seems to good to be true. It also looks quite nice and looks like it would fit snug in the position of the ash tray (which is good as im not a smoker).

If anyone can shed any light on this product whether its reliable and how it preforms, etc, it would be greatly appreciated.

Thanks

http://www.hikariperformance.com/new_electronics.htm

(scroll rite to the bottom)

elect%20boost%20cont.jpg

Link to comment
https://www.sau.com.au/forums/topic/10481-hybrid-electronic-boost-controller/
Share on other sites

I was told but am not 100%sure that they are like a electronic version of the turbosmart type 2 stage bleed valve setup, so they are not as accurate as controlling boost like good elec ones they just give you control in the cabin.

They are nothing like the TS twin stage they do run a micro processor

seen in two cars now work well but you need to have a map sensor of some type ..... like you need to tap into say the std dash map on r32/33 but on somthing like a s13 you'll need to hunt a map sensor down

I sent power digger an email.

Heres what i sent:

Hi

I wondering if you could supply me with as much info as u can on the Hybrid fully electronic boost controller. How does it work through the microprocessor? Is it like an AVCR, or not as indepth and efficient. Will it hold high boost levels, and will the boost levels spike due to it being a bleed valve type boost controller. Im very serious on buying one, just want more info before i make my decision.

Thanks

Dean

And heres his reply

thanks for your interest it has a micro built in and by sensing the boost signal the micro calculate the right boost amount

in other words it try to bring the boost up to preset level as soon as possible and soon after it reaches the preset boost it regulated it

never over shoot

beside it is not a bleed type valve it is a proper 9 bar solenoid valve that uses in many other Japanese boost controller

Thanks

  • 3 weeks later...

Hi all,

I have installed the hybrid boost controller. I have to say it was the easiest ebc install(just three wires, the same three that run to the factory boost reciever in the engine bay) i have ever done!!

Very easy to tune, just set the dials for hi/low boost.

On the road it holds boost and at 20psi is only only slightly shaking the needle on the boost gauge (not more than half a psi either way.

As for brining boost on earlier I noticed a little differance

install 9/10

tunability 10/10

boost holding 8/10 (twin solonoid would have been better)

Appearance 4/10 (only one blue led and no screen as per avcr)

All in all not bad for $325 delivered

  • 3 weeks later...

Hi There,

I also noticed the "powerdigger" at UAS (for $380).

Seems like a really good buy.

Quick question for those who have installed it.

- Does the car fill "jerky" when on full boost as some one mentioned that is was changing half a psi up and down (at 20 psi).

I am only planing to run 12 psi, will I notice it? How smooth is it under boost?

- when it comes to installing it, where is the "map sensor" or "boost sensoe" what ever it is called... I should have no problems installing it just need to find that boost sensor (for an R33 gts-t)

Thanks for your answers.

Regards

Rob

Hi Rob the car is not jerky when on boost, even though the boost needle is moving. When you get the intstructions it has a picture of the boost sensor and how to wire it all up. The boost sensor should be on the left hand side of the firewall. easy to spot if you know what your looking for.:)

If anyone else has installed one please write your comments, as I wonder if it is any differant on a smaller tubo, unlike mine which has a fair bit of lag.????

Ps go to hikari they are $325 delivered

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...