Jump to content
SAU Community

Recommended Posts

Hey all,

Just wondering if the Stagea can SAFELY be run in RWD like the GTR's by removing the ATTESA fuse or something similar. Or is it much harder / impossible to do like removing front drive shafts like the R34 GTR.

And also how many of you have played around with the AWD lock button on the dash. I'm assuming that all it does is lock it into full time AWD. Noticed much difference????

Thanks again

Josh

Link to comment
https://www.sau.com.au/forums/topic/105015-rwd-stagea/
Share on other sites

The ATTESSA system in the Stagea S! is like the R33GTR, NOT like the R32GTR. This means it has residual hyrdraulic pressure, so pulling the fuse does nothing.

Do a search, Brad explains what happened to his Stagea when someone tried the R32GTR trick.

The 4wd switch is good for snow and ice and wet grass. Do a search, it was a much discussed subject when we early adoptors got our Stageas 18 months or so back.

:( cheers :(

Link to comment
https://www.sau.com.au/forums/topic/105015-rwd-stagea/#findComment-1933428
Share on other sites

warning, dont believe those first few posts on that thread ska mentions, its gonna damage the clutch packs pulling a fuse, and even bleeding the attessa line does bugger all, except smoke clutch packs on a dyno.

i explained my method in the thread, which i believe is the best/safest way of running rwd, though maybe removing the front driveshaft is easy except u gotta take of the clutch slave cylinder off the gearbox to get it out, or remove the clutch hydraulic line from the slave.

mine was suprisingly grippy running 350rwhp and held better than my previous 2wd car with the rb26 in it (commodore). i think they have alot better suspension setup and only drama was i snapped an axle on the rear diff from launching off a set of lights, as the diff is non-lsd and all the power is going through one wheel only, but i chucked in the gtr lsd and its much better, though i havent used it stuff all since the diff conversion.

in about 3-4 weeks when mines tuned we shall see what power these stageas need to wreck gtr axles/uni joints :P

i just wanna see if the stagea will drift nicely in 4wd and ill try 2wd also.

good luck

Brad

Link to comment
https://www.sau.com.au/forums/topic/105015-rwd-stagea/#findComment-1933858
Share on other sites

do NOT drive around on tarmac with the centre diff lock enabled. you will get wind up in the driveshafts and diffs and will eventually break one,if not the transfer case as well.

use the diff lock on slippery surfaces such as dirt,sand or snow ONLY.

you can most likely fit an ATTESSA control module,which will give you the option of a more rear-biased split. I'll be trying this fairly soon on my car.

Justin...

Link to comment
https://www.sau.com.au/forums/topic/105015-rwd-stagea/#findComment-1933977
Share on other sites

Ok thanks guys. SKA I did try to use the search but it wasn't working. Kept telling me to try again in 30secs because of flood controll or something like that. I tried for ages and gove up posting this thread. I haven't even tried the centre diff lock yet and can't really see when I would.

fergo308 let us know how you go with the ATTESSA control module. I love the AWD but would still like to get it into RWD on occasion.

Link to comment
https://www.sau.com.au/forums/topic/105015-rwd-stagea/#findComment-1934132
Share on other sites

Brad, does the LSD centre drop into the standard diff casing?

I'm still scared to launch my car off the lights in case I break a driveshaft. It doesn't help that my car was fitted with a ceramic button clutch when it was converted.

Regardless, it always bogs down anyway, so harder launches will be required when I wanna run some times.

Oh yeah, and I might be attending the SAU dyno day next month, but it's a 2wd dyno. They've said removing driveshafts will be part of the cost of the run, but now that you mention removing the slave cylinder or hydraulic line throws a new spanner into the works. I'm assuming they know this and it's the same as R33 GT-Rs?

Cheers

Nick T.

Link to comment
https://www.sau.com.au/forums/topic/105015-rwd-stagea/#findComment-1934865
Share on other sites

Brad, does the LSD centre drop into the standard diff casing?

I'm still scared to launch my car off the lights in case I break a driveshaft.  It doesn't help that my car was fitted with a ceramic button clutch when it was converted. 

Regardless, it always bogs down anyway, so harder launches will be required when I wanna run some times.

Oh yeah, and I might be attending the SAU dyno day next month, but it's a 2wd dyno.  They've said removing driveshafts will be part of the cost of the run, but now that you mention removing the slave cylinder or hydraulic line throws a new spanner into the works.  I'm assuming they know this and it's the same as R33 GT-Rs?

Cheers

Nick T.

hey nick, yep the gtr diff centre drops str8 in, as its exactly the same housing except the stagea one has the mountings for all the attessa pumps above the diff, which makes it a bolt back in job. im not sure about trying to use stagea axles with the gtr diff as i never tried it personally.

removing the clutch slave cylinder is only 2 bolts and then pull the front shaft off and then bolt the slave back on (dont need to release the clutch fluid or take the line off or nuthin) and away u go. (just move it to the side while u pull the shaft out from under the car)

all up removing the shaft and slave would take 10-15 min max.

hope it helps

Brad

Link to comment
https://www.sau.com.au/forums/topic/105015-rwd-stagea/#findComment-1935226
Share on other sites

the ONLY way to safely make the car RWD is to drop the shaft.

Its honestly not that hard people. 4 bolts and away you go. I was having a look around yesterday.

When i get an LSD i will make the car RWD for some fun, i know ill still have those extra 4wd kg's but we shall see.

Link to comment
https://www.sau.com.au/forums/topic/105015-rwd-stagea/#findComment-1944277
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, plenty of air flow, there is a dedicated path that feeds the air in to the OEM intake tube behind the bumper As for a "tangible effect", maybe, but getting the pod/intake air out of the hot engine bay is worth it psychologically to me, even if it gives no performance difference, so the tangible effect in my Lizard brain saysss yessss  In the end, to me a tangible effect isn't always about performance, sometimes it a sound or a look, or even a...... feeling  Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga Ooga-Chaka Ooga-Ooga
    • yeah first and reverse is where you will find clutch release issues (whether hydraulic or mechanical) because the difference in revs required is the highest there; particularly changing down from 2nd to 1st when still moving. To be clearer though, it is possible that the clutch release bearing is the wrong height. This is less likely than a hydraulic issue but it is not unheard of when you are mixing and matching
    • Quite right, if you make it to that pension you deserve every cent
    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
×
×
  • Create New...