Jump to content
SAU Community

Recommended Posts

Hi all.

I want to go to wsid, but I want to break into high 12's....

At the moment Hybrid FMIC, filter, mongrel exhaust, locked diff, 4 puck clutch, fuel pump 040??, Dr Drift Ecu, r33 turbo,no interior bar two front seats. 255 rears on 17's. adj cam gears to go on (180rwkw?)

I'm curious if this will achieve a high 12, or do I have a little bit to go yet???

What are your experiences in breaking 13's???

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/105416-173rwkw-32-gts-t-14/
Share on other sites

My R32 when i had the RB20 in ran a few 12.9 @116mph on 225/45/17" street tyres.

It only made 188RWKW with a small hi-flow turbo, intercooler, 3" exhaust and ECU, so it CAN be done you just need another 15rwkw or so.

That MPH is MASSIVE for only 188rwkw!

That MPH is MASSIVE for only 188rwkw!

Yeah, the MPH is a bit higher than my VL which had 200rwkw and ran 12.6@112MPH.

Ill try and get the timeslip up, my car was car# 600, i cant find the actual 12.9 with 116mph, but here is a 12.9 sec slip and one when i started pulling 116mph.

post-11223-1139734276.jpg

sky30, thats a brilliant result

the best i managed was 13.1 @ 108mph with 225/50/16 street tyres and standard suspension. That was on about my 8th run of the day.

i was making 207rwkw with a hks2530 and ~1.25bar

but sky30's time makes my efforts look dismal!

173rwkw = 13.3@106mph (2.3 60ft) on 205 tyres R33 gtst. 33 deg ambient.

Dyno numbers don't tell you everything. I recently thought of tracking the time over the x axis for rpm. This way you can track the accelleration times under load in each gear. This will directly translate to a relative 1/4 mile prediction as things like rotational mass greatly affect accelleration and can be shown using this measurement, without it you can't see the benifit. The physical weight of the car and areodynamics are then the only factors left to associate.

Next time you go to the dyno get your stop watch out and see how long it takes to make the power. Bolt in a lightweight flywheel or lighter rims, change the diff ratio and see just how big an influence these things can have.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...