Jump to content
SAU Community

Recommended Posts

Hi all, just wondering how many of you's out there have wound some boost into your cars?

We run 10 pound all day everyday.

What is everyones idea of a safe boost level to run?

Also what sort of fuel ecconomy do you guys get now?

Link to comment
https://www.sau.com.au/forums/topic/105442-what-boost-do-you-run-in-the-stagea/
Share on other sites

... you's ....

Sorry, firstly a pet hate of mine, it's 'you', plural and singular.

And on topic, i run my bleed valve at 10psi as over that the stock stagea computer has a fuel cut and the car jerks around. not a fun experience.

I'm getting about 350 - 370km to a tank city driving and over 450km to a tank country driving

I've got the jaycar IEBC set at 10 pound on high boost setting. With the stock (well I've got an R34GTT but close enough) intercooler and turbo I won't run any higher than this. I also doubt if I did I'd get much more power anyway. As it is even though my guage only just flickers about the 10 at times I still hit boost cut when I push hard between gear changes (auto).

i'm not having a real fun time with fuel atm as most people here will tell you. If I can get it over 300k's city i'm doing well atm. But I've only just bought it and am now learning how to drive it for better economy (= baby it). on my current tank i'm at 70k's and in between 3/4 and full so its looking better already.

mine is running 11 with the uni chip, seems much better than standard but missing under load, think its the coil packs. getting about 280 to 300kms a tank city driving, but i do have a bit of a heavy foot

It's prob a good idea if you add if you have the standard turbo, exhaust & any other mods.

Mine is stock except for a splitfire filter, & i run around 10, but i find at around 5000rpm it feels like a stutter in the power band & i got no idea what it is?

0 boost for the last 8 months haha, and before that was 18psi with 350rwhp for about a month, and before that it was stock 7psi with the rb25.

soon to run 17-18psi as a base tune, and then in a few months hoping to put in over 2bar and push the t04z to its limit :D

Well currently I'm running 8 - 9psi...

When I get the Jaycar IEBC installed etc. I will be running 10psi low and 14.7 (1 bar) on high.

Fuel economy sucks :P Cant really get over 350 no matter how hard I try

Once I get it tuned properly I want to run about 10 psi, as the stock rb25 turbo's do not respond well to anything over 1bar for prolonged periods, or so I have been told and read on here, (there are thousands of threads on this subject).

But I was getting about 400kms out of a tank, but that was with the pfc tuned with a blocked radiator at the time, so it was tuned stupidly rich.

I have to clean the back screen at least once ever three to four days otherwise it gets blocked by that unburnt fuel soot :(

Hopefully in the next couple of weeks it will be tuned properly on 10psi, and I will be aiming for ~500kms out of the tank, hopefully :P

Quote SKA -

I have to clean the back screen at least once ever three to four days otherwise it gets blocked by that unburnt fuel soot"

Q was, what is the back screen? is it just the rear window?

I thought at first it may have been something on the intake causing your fuel rich problems. I suppose I had in my mind what others have said about cleaning their AFM's.

I just wanted to be up to speed with my servicing before it became a problem.

After reading some of these threads it seems that most people have a squeak/rattle or misfire problem somewhere. Everytime I drive mine I listen out for things and have yet to fault anything. (except for the noise in my left ear saying "slow down you've got kids (3) in the back!")

It runs flawlessly and I love it more each time I drive it.

OH OH OH Sorry :D Rear Screen = Rear Windscreen :)

And its the whole back door and rear bar, that whole area gets covered in black soot, but I am sure it is because I am running stupidly rich, I leave a HUGE black cloud of fuel smoke when I do launch it :D

Currently running 10 psi controlled by the IEBC with the DFA tuned (~11 to 1 A/ F ratio) which was as good as we could get it with the standard exhaust. The R34GTT intercooler is fitted but the Magic cat is still in the garage with the 3.25” exhaust. Plus the SITC is fitted, but untuned, it is waiting on the exhaust.

Now that the project R33GTST is serviced, registered, suspended, PFC’d and running hard and fast, I might be able to get back to the Stagea. There is also a GCG ball bearing high flow and a split dump/engine pipe to go on.

BTW, It was pretty useless running more than 7-8 psi without the DFA, the standard ECU R&R mapping made it slower than when it ran 6 psi.

:D Cheers :)

Edited by Sydneykid

Running 12psi. All fully tuned.

Full exhaust, fmic, NEW oxygen sensor (for best fuel economy), pod filter, sitc, safc, ebc etc etc.

Get over 420km per tank (hitting resevre), with 160awkw.

Great pick up at 5000rpm, no splutter for me - a nice safe tune, rarely do I let it stay at 12psi....... (heat factor = dead turbo).

Got a spare turb' sitting on the shelf.......

my car is completely stock except for the 3.5" exhaust, front mount, and pod filter.

plannin some more mods down the track.

but I don't wanna go crazy.

keepin in mind that this is my daily run about family car.

if my other half had his own way it would have had a turbo upgrade and computer by now.

but in the end it's my car and the foot comes down...

lol....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That looks good, but I think you're going to need much beefier side skirts now.
    • They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • Define "starting to fail". Wy not just rebuild them?
    • Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...