Jump to content
SAU Community

Recommended Posts

The Stagea has a vibration at speeds above around 80kmh. At first I thought it was a puncture repaired front left tyre but got that fixed and even swapped the front wheel to the back but it is still there.

Wheels have been balanced by at least 3 different places now, so not sure what is causing this. It feels like out of balance wheels but have been told it isn't, doesn't feel like an out of round wheel (my Skyline had that problem). It is a very fast but weak vibration and doesn't seem to do it at lower speeds, that I can notice.

Following a search of the threads, found this list from our guru (Sydneykid):

1. Out of balance tyres (are they balanced inner and outer? Or just one set of weights?)

2. Out of round tyres (easy to check on the balancer)

3. Out of centre wheels (do they lock securely over the hub centre?)

4. Out of round wheels (how is the run out on the inner and outer rims?)

5. Out of balance brake rotors (unusual, but does happen)

6. Worn wheel bearings (jack it up and check the movement, in and out top and bottom)

7. Worn radius rod bushes (you can see it, the rubber is torn and fluid leaking)

After that it gets obscure, eg; worn shocks can cause vibration after hitting a bump.

Therefore, should I just check each of these items in turn until find something?

Further, during my 100,000km service, the workshop noted something along the lines of front diff oil seal leaking - is this a major repair issue or just a case of replacing seals?

Link to comment
https://www.sau.com.au/forums/topic/105479-driveline-vibration-at-80kmh/
Share on other sites

mate its probably uni joints .... one has a tolerance out and is causing an unbalance vibration ... either that or you have thrown a tailshaft weight off (rare)

test by taking car to 80kms then coast (no drive) to see if it still vibrates usualy it will if its the tail shaft uni's as the tail shaft is rotating as fast as the wheels are driving it ...

Good luck!

Further, during my 100,000km service, the workshop noted something along the lines of front diff oil seal leaking - is this a major repair issue or just a case of replacing seals?

hey mate do u mean the diff front plate seal, or the sump to engine seal is leaking? the diff front plate is piss easy and the other is a pain in the arse. :P

just take front plate off, add gasket goo from nissan and put back on :(

Edited by CruiseLiner

check the tailshaft centre bearing would be my suggestion,if you've already eliminated the wheel bearings,wheels and tyres.

it's possible someone has had the shaft out before and put it back in in a different orientation. normally this won't cause a problem,but if you have a worse-than-usually-balanced shaft,it would cause what you're describing.

just out of interest,how much balancing weight is on your wheels?

if there's a lot (as in over 50grams per side),that's indicative of another problem.

Justin...

Thanks for the replies guys and it is now time to begin the hunt to determine the cause of the problem and then the fix.

Will see how it goes but at least it is still driveable

As for your question Brad, not sure as they just put it on the invoice that the "front diff seal leaking".

Sorry to hi-jack your thread, but I've got a similar problem.. I get steering wheel vibration above around 80km/h. I took it to get a balance but the guy said the vibration is because of the tyres. He said because of how the tyres have worn they are impossible to balance. He said you can try balancing them as much as you want but the vibration isn't going to go away so he'd just be 'taking my money'. He said the tread had 'feathered' and that you can tell by running your hand over the tyres. So he says I need to get new tyres to fix the problem. Could this be true or he is just trying to get me to buy new tyres??

Feathering on tyres is caused by the wheels not being aligned properly.

Get a wheel alignment done. If you buy new tyres without getting the wheels aligned, the same problem will happen and you would have wasted your money on tyres.

Thanks champ. Yea they did a wheel alignment. So this 'feathering' thing actually happens? Just get new tyres fitted and balanced and it should be good? Thanks again.

Just to add another suggestion:

Check that the casing of the tyre isn't letting go. This may show up as a deformation in the shape of the tyre - like a lump/bulge in the wall or flat part of the tread.

On a tyre on our caravan the deformation was hardly noticable at all except for the vague handling at speed.

The amount of tread left (ie age of the tyre) has little to do with it. Hitting a gutter or rock on the road may be enough to damage something internally.

If you're worried about getting had on a new set of tyres when the current tyres have plenty of life left, then keep the old set of tyres to use again later. If the new set fixes the problem then you know you can throw the old ones.

The Stagea has a vibration at speeds above around 80kmh.  At first I thought it was a puncture repaired front left tyre but got that fixed and even swapped the front wheel to the back but it is still there.

Wheels have been balanced by at least 3 different places now, so not sure what is causing this. It feels like out of balance wheels but have been told it isn't, doesn't feel like an out of round wheel (my Skyline had that problem).  It is a very fast but weak vibration and doesn't seem to do it at lower speeds, that I can notice.

Following a search of the threads, found this list from our guru (Sydneykid):

1. Out of balance tyres (are they balanced inner and outer? Or just one set of weights?)

2. Out of round tyres (easy to check on the balancer)

3. Out of centre wheels (do they lock securely over the hub centre?)

4. Out of round wheels (how is the run out on the inner and outer rims?)

5. Out of balance brake rotors (unusual, but does happen)

6. Worn wheel bearings (jack it up and check the movement, in and out top and bottom)

7. Worn radius rod bushes (you can see it, the rubber is torn and fluid leaking)

After that it gets obscure, eg; worn shocks can cause vibration after hitting a bump.

Therefore, should I just check each of these items in turn until find something?

Further, during my 100,000km service, the workshop noted something along the lines of front diff oil seal leaking - is this a major repair issue or just a case of replacing seals?

Hey

I had a similar problem with my GTR. Driveline started to vibrate on medium to hard acceleration and only when it was about 70km/h and over.

First thing to be done was the centre bearing, did look pretty worn but didnt fix it.

Wheel alignment and balance on 2 different sets of wheels. Checked all rear bushes and links.

Replaced front prop shaft as the uni joint was pretty flogged out (wasn't affecting vibration as it wouldnt make any difference with this shaft out ie 2WD).

Replaced small rubber and metal sleeve mounts for gearbox crossmember, again, worn out but didnt fix problem.

Took out tailshaft and put back in but rotated it around from original position. From what the mechanic told me there is 4 different ways for it to go back in. He moved it one mounting positon around and it was all fixed. :P

It took a bit of money and research to get it sorted for an annoying problem but probably was a good thing to get all these worn out bits n pieces replaced before they broke or caused potential damage.

Jono

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nice, thanks for sharing your progress....that's a pretty long list you are putting into it!
    • Decided to upgrade my pressurised plastic coolant expansion tank for a fancy pants alloy version The OEM versions can get brittle, even the new plastic one I got when I first got the car is a starting to show signs of "stress" I wasn't cheap, but it is basically unbreakable
    • Morning all, I have an RB25DET Neo that's in need of a rebuild. Will need new pistons etc due to detonation damage. Would anyone be able to recommend a shop in Southeast Queensland who I could bring my long motor to for a rebuild? Just want someone who knows RBs and whos built a bunch of them before. TLDR - recommended engine shops for RB rebuild.
    • Gday Thought it was about time I started a build thread! As expected this project has snowballed into a huge financial liability, but unless you’re strong willed and responsible, it’s not a surprise. Background -  My first turbo car was an R32 GTS-4, got my full license and then totalled my Au Falcon a week later, so while trying to sell my RMZ450 dirtbike to buy another car a bloke offered to swap the R32 which at the time I felt like I was ripped off but looking back and seeing prices of those now ($40kish) it was a good deal, I didn’t know enough about these cars to appreciate what I had so sold it before the RB20 blew up. Between here and there, out of 12 cars I’ve owned the note worthy ones are a V8 Lexus SC400 (soarer), a couple of XR6 Turbos and my beloved S15 which I had for about 3 years, picked it up for $12500, repairable write off but she was fine, gun metal grey/pewter and bone stock/unmolested until I got my hands on it. Ended up spending about the value of the car and 280kw, 2 demerit points by the time I got defected and sold it for $14500 (also $40kish in today’s market, rip) Fast forward to the present day, I’m in a much better position financially and daily an MQ Triton (great cars, pipe down Ranger Bois), I cruised marketplace and car sales for a few months looking for another R32, the best deal I could find was an absolute rust bucket half finished project for $12000, until this R33 popped up in Port Macquarie for $18k - unregistered and barely running but decent shape, kept an eye on it for a few weeks and the price steadily dropped, $16k then $15k then $14k, that was the point where I was like shit someone’s gonna snatch this up! It was owned by a young bloke who had big plans but him and his missus just had a baby so smartest move financially for them but big gain for me. So 2 days later I’m towing a car trailer to pick this thing up. Roughly 2 weeks and $3500 later I’m cruising around Newcastle in my beat up R33 all smiles and dose noises! It only needed some basic shit to get it going, coil packs and air flow meter, electrical stuff and all fluids changed, 158k kms and running pretty good, nice smooth engine after oil and coolant flush - when I say coolant I mean it had been filled up with tap water, every gallery and heater element was filled with rust, 8-9 flushes later and still had brown liquid coming out but she’ll be right. The car was painted R34 Bayside Blue at some point but whether it was a cheap job or just not looked after is anyone’s guess, clear coat flaking like sausage roll.  Was rethinking my choices and contemplating life, had it up for sale for $22k - still cheaper than any registered R33 but got little interest, next minute I had an opportunity at work - 6 months overseas for good money, so that was a no brainer, fast forward again and here we are with a 50% finished project. Current Mods - 200ish KW according to butt dyno Was tuned with Apexi PowerFC EBC (old school Greddy Profec)  Stock turbo (more shaft play than a Tinder date gone right) 3inch turbo back Varex muffler  Aftermarket injectors of mystery size, Power FC showed 36% duty cycle at full boost so not behd good size Someone had good intentions but stuck with the stock R33 MAF so we had misfires at 6000rpm due to the MAF hitting 5.2V So far I’ve redone the entire interior with carpet form Car Mats Direct, new Seats and steering wheel from Autotechnica, also sound system by Autobarn (mainly Kicker) Also MCA pro comfort coil overs - Hands down best purchase yet, worlds of improvement over the tired 30yrold shocks Goals - 450kw/600hp on flex tune New paint job - Midnight Purple 2 Engine is at the shop getting rebuilt with forged rods a pistons, new valves and springs, ATI Harmonic balancer, Aeroflow 7.5L sump, rear head drain and oil restrictors as per oil control thread* and cam covers modded for larger breathers, other stuff I can’t recall of the top of my head Parts purchased and to be installed once the engine is done -  Engine loom from Wiring Specialties including these options: Haltech Nexus S3 R35 Coil pack conversion  PRP Dual Trigger kit Fan controller  Other Parts -  262 Kelford Cams Turbo - Hypergear ATR43SS3-ProS with T51R mod (whistly boi) 6 boost manifold (high mount) 50mm Turbosmart Pro gate (plumbed back for legal reasons) HKS Super Turbo Exhaust with High Flow Cat Custom 3.5inch dump and front pipe 1500cc Bosch injectors  Fuel Pump walbro 525 Haltech MAP and IAT sensors Haltech Flex Sensor Fenix Radiator with dual thermo fans LS1 Alternator Kit Oil Filter Relocation from EFI solutions and Cooling pro oil cooler Many other things sitting in my garage waiting for that engine to come back. Progress pics to follow -  
    • Losses have to be less with DC coupling. Provided the battery inverter has decent MPP tracking ability - which really shouldn't be a problem. It's not 2005 any more.
×
×
  • Create New...