Jump to content
SAU Community

Recommended Posts

The Stagea has a vibration at speeds above around 80kmh. At first I thought it was a puncture repaired front left tyre but got that fixed and even swapped the front wheel to the back but it is still there.

Wheels have been balanced by at least 3 different places now, so not sure what is causing this. It feels like out of balance wheels but have been told it isn't, doesn't feel like an out of round wheel (my Skyline had that problem). It is a very fast but weak vibration and doesn't seem to do it at lower speeds, that I can notice.

Following a search of the threads, found this list from our guru (Sydneykid):

1. Out of balance tyres (are they balanced inner and outer? Or just one set of weights?)

2. Out of round tyres (easy to check on the balancer)

3. Out of centre wheels (do they lock securely over the hub centre?)

4. Out of round wheels (how is the run out on the inner and outer rims?)

5. Out of balance brake rotors (unusual, but does happen)

6. Worn wheel bearings (jack it up and check the movement, in and out top and bottom)

7. Worn radius rod bushes (you can see it, the rubber is torn and fluid leaking)

After that it gets obscure, eg; worn shocks can cause vibration after hitting a bump.

Therefore, should I just check each of these items in turn until find something?

Further, during my 100,000km service, the workshop noted something along the lines of front diff oil seal leaking - is this a major repair issue or just a case of replacing seals?

Link to comment
https://www.sau.com.au/forums/topic/105479-driveline-vibration-at-80kmh/
Share on other sites

mate its probably uni joints .... one has a tolerance out and is causing an unbalance vibration ... either that or you have thrown a tailshaft weight off (rare)

test by taking car to 80kms then coast (no drive) to see if it still vibrates usualy it will if its the tail shaft uni's as the tail shaft is rotating as fast as the wheels are driving it ...

Good luck!

Further, during my 100,000km service, the workshop noted something along the lines of front diff oil seal leaking - is this a major repair issue or just a case of replacing seals?

hey mate do u mean the diff front plate seal, or the sump to engine seal is leaking? the diff front plate is piss easy and the other is a pain in the arse. :P

just take front plate off, add gasket goo from nissan and put back on :(

Edited by CruiseLiner

check the tailshaft centre bearing would be my suggestion,if you've already eliminated the wheel bearings,wheels and tyres.

it's possible someone has had the shaft out before and put it back in in a different orientation. normally this won't cause a problem,but if you have a worse-than-usually-balanced shaft,it would cause what you're describing.

just out of interest,how much balancing weight is on your wheels?

if there's a lot (as in over 50grams per side),that's indicative of another problem.

Justin...

Thanks for the replies guys and it is now time to begin the hunt to determine the cause of the problem and then the fix.

Will see how it goes but at least it is still driveable

As for your question Brad, not sure as they just put it on the invoice that the "front diff seal leaking".

Sorry to hi-jack your thread, but I've got a similar problem.. I get steering wheel vibration above around 80km/h. I took it to get a balance but the guy said the vibration is because of the tyres. He said because of how the tyres have worn they are impossible to balance. He said you can try balancing them as much as you want but the vibration isn't going to go away so he'd just be 'taking my money'. He said the tread had 'feathered' and that you can tell by running your hand over the tyres. So he says I need to get new tyres to fix the problem. Could this be true or he is just trying to get me to buy new tyres??

Feathering on tyres is caused by the wheels not being aligned properly.

Get a wheel alignment done. If you buy new tyres without getting the wheels aligned, the same problem will happen and you would have wasted your money on tyres.

Thanks champ. Yea they did a wheel alignment. So this 'feathering' thing actually happens? Just get new tyres fitted and balanced and it should be good? Thanks again.

Just to add another suggestion:

Check that the casing of the tyre isn't letting go. This may show up as a deformation in the shape of the tyre - like a lump/bulge in the wall or flat part of the tread.

On a tyre on our caravan the deformation was hardly noticable at all except for the vague handling at speed.

The amount of tread left (ie age of the tyre) has little to do with it. Hitting a gutter or rock on the road may be enough to damage something internally.

If you're worried about getting had on a new set of tyres when the current tyres have plenty of life left, then keep the old set of tyres to use again later. If the new set fixes the problem then you know you can throw the old ones.

The Stagea has a vibration at speeds above around 80kmh.  At first I thought it was a puncture repaired front left tyre but got that fixed and even swapped the front wheel to the back but it is still there.

Wheels have been balanced by at least 3 different places now, so not sure what is causing this. It feels like out of balance wheels but have been told it isn't, doesn't feel like an out of round wheel (my Skyline had that problem).  It is a very fast but weak vibration and doesn't seem to do it at lower speeds, that I can notice.

Following a search of the threads, found this list from our guru (Sydneykid):

1. Out of balance tyres (are they balanced inner and outer? Or just one set of weights?)

2. Out of round tyres (easy to check on the balancer)

3. Out of centre wheels (do they lock securely over the hub centre?)

4. Out of round wheels (how is the run out on the inner and outer rims?)

5. Out of balance brake rotors (unusual, but does happen)

6. Worn wheel bearings (jack it up and check the movement, in and out top and bottom)

7. Worn radius rod bushes (you can see it, the rubber is torn and fluid leaking)

After that it gets obscure, eg; worn shocks can cause vibration after hitting a bump.

Therefore, should I just check each of these items in turn until find something?

Further, during my 100,000km service, the workshop noted something along the lines of front diff oil seal leaking - is this a major repair issue or just a case of replacing seals?

Hey

I had a similar problem with my GTR. Driveline started to vibrate on medium to hard acceleration and only when it was about 70km/h and over.

First thing to be done was the centre bearing, did look pretty worn but didnt fix it.

Wheel alignment and balance on 2 different sets of wheels. Checked all rear bushes and links.

Replaced front prop shaft as the uni joint was pretty flogged out (wasn't affecting vibration as it wouldnt make any difference with this shaft out ie 2WD).

Replaced small rubber and metal sleeve mounts for gearbox crossmember, again, worn out but didnt fix problem.

Took out tailshaft and put back in but rotated it around from original position. From what the mechanic told me there is 4 different ways for it to go back in. He moved it one mounting positon around and it was all fixed. :P

It took a bit of money and research to get it sorted for an annoying problem but probably was a good thing to get all these worn out bits n pieces replaced before they broke or caused potential damage.

Jono

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...