Jump to content
SAU Community

Recommended Posts

Hey,

Last week, I have a slight problem with my battery I think. My R33 wouldn't start after 2 or 3 weeks and I had to jump it to get the car going. It's okay now, since I drive it every day. However I would like to know if it's about time to change the battery, which is purchased in March 2003.

Do I need a battery soonish? What CCA and RC rating should I be looking at? What brands do people recommend?!

Thanks in advance!!

/Andy

Link to comment
https://www.sau.com.au/forums/topic/105500-flat-battery-after-2-or-3-weeks/
Share on other sites

The higher the cranking amps, the better... although don't forget that your clock and A/C settings are always using a *little* power, and if you have an alarm, it'd suck a bit too. The ECU keeps its self-learning stuff, and i'm sure your headunit does too.. These add up, and it could drain a battery over the course of almost a month.

If you're going to change the battery anyway, it won't do any harm and shouldn't cost you more than $200 for a really good battery.

Higher CCA and higher number of plates will be the cost-factor. =-]

a good battery should not go flat in that amount of time on a stock car..

your options:

1 - as you said it could be a flat battery. theyare usually rated at about 4 years lifetime.. so how old is yours?

2 - you may have something draining power. Do you have an amplifier? neons? some other lights? if they aren't wired in properly then they could be draining power when the car is off..

good luck,

Warren

Andy, mine's just a little 330cca. My factory strut-brace meant that I couldn't run a larger battery.

By "larger" I mean;

More powerful batteries are usually bigger in physical size too. The R33 Skyline battery holder will allow two different sizes of batteries, but I had to use the smallest type to avoid removing my strut-brace.

Warren has a point, if the car is totally stock (read: no alarm an aftermarket ECU/head unit) then it should probably hold the charge for several months infact. You might be able to use a multimeter to ascertain how much current draw is on the battery while the car is off. (apart from the boot light which will be on while you test the battery!)

your options:

1 - as you said it could be a flat battery. theyare usually rated at about 4 years lifetime.. so how old is yours?

My battery is almost 3 years old, and don't find any problems if I drive it everyday.

---

Andy, mine's just a little 330cca. My factory strut-brace meant that I couldn't run a larger battery.

By "larger" I mean;

More powerful batteries are usually bigger in physical size too. The R33 Skyline battery holder will allow two different sizes of batteries, but I had to use the smallest type to avoid removing my strut-brace.

My local auto-electrician recommend what they stock:- fully sealed battery with 430CCA. Does more CCA mean anything after the car is running??

get your alternator checked out mate!!

I will definitely get that checked too...

thanks for the advice guys~

Get your auto electrician to check the 'parasitic' load. Some component of the car might be draining too much power when its off. It should be be under 50mA. I know my car goes flat after 2 weeks cos my parasitic load is roughly 100mA which is definitely too much.

God knows what component it is though. I suspect its my shitty alarm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...