Jump to content
SAU Community

Recommended Posts

Hey,

Last week, I have a slight problem with my battery I think. My R33 wouldn't start after 2 or 3 weeks and I had to jump it to get the car going. It's okay now, since I drive it every day. However I would like to know if it's about time to change the battery, which is purchased in March 2003.

Do I need a battery soonish? What CCA and RC rating should I be looking at? What brands do people recommend?!

Thanks in advance!!

/Andy

Link to comment
https://www.sau.com.au/forums/topic/105500-flat-battery-after-2-or-3-weeks/
Share on other sites

The higher the cranking amps, the better... although don't forget that your clock and A/C settings are always using a *little* power, and if you have an alarm, it'd suck a bit too. The ECU keeps its self-learning stuff, and i'm sure your headunit does too.. These add up, and it could drain a battery over the course of almost a month.

If you're going to change the battery anyway, it won't do any harm and shouldn't cost you more than $200 for a really good battery.

Higher CCA and higher number of plates will be the cost-factor. =-]

a good battery should not go flat in that amount of time on a stock car..

your options:

1 - as you said it could be a flat battery. theyare usually rated at about 4 years lifetime.. so how old is yours?

2 - you may have something draining power. Do you have an amplifier? neons? some other lights? if they aren't wired in properly then they could be draining power when the car is off..

good luck,

Warren

Andy, mine's just a little 330cca. My factory strut-brace meant that I couldn't run a larger battery.

By "larger" I mean;

More powerful batteries are usually bigger in physical size too. The R33 Skyline battery holder will allow two different sizes of batteries, but I had to use the smallest type to avoid removing my strut-brace.

Warren has a point, if the car is totally stock (read: no alarm an aftermarket ECU/head unit) then it should probably hold the charge for several months infact. You might be able to use a multimeter to ascertain how much current draw is on the battery while the car is off. (apart from the boot light which will be on while you test the battery!)

your options:

1 - as you said it could be a flat battery. theyare usually rated at about 4 years lifetime.. so how old is yours?

My battery is almost 3 years old, and don't find any problems if I drive it everyday.

---

Andy, mine's just a little 330cca. My factory strut-brace meant that I couldn't run a larger battery.

By "larger" I mean;

More powerful batteries are usually bigger in physical size too. The R33 Skyline battery holder will allow two different sizes of batteries, but I had to use the smallest type to avoid removing my strut-brace.

My local auto-electrician recommend what they stock:- fully sealed battery with 430CCA. Does more CCA mean anything after the car is running??

get your alternator checked out mate!!

I will definitely get that checked too...

thanks for the advice guys~

Get your auto electrician to check the 'parasitic' load. Some component of the car might be draining too much power when its off. It should be be under 50mA. I know my car goes flat after 2 weeks cos my parasitic load is roughly 100mA which is definitely too much.

God knows what component it is though. I suspect its my shitty alarm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
×
×
  • Create New...