Jump to content
SAU Community

Heaps Of Stuff, Engines Parts Etc

fangns13
 Share

Recommended Posts

fangns13 Contributor

fangns13

Posted
Posted

Cleaning out my garage and have heaps of crap sitting around:

3 x RB20DET engines no turbos or loom, sell whole or parts $350 each

1 x RB25 NA bottom end $100

1 x SR20 NA bottom end with alternator and starter motor $200

R33 2WD Engine crossmember $100

Also have my RB30DET project, RB25 VVT head, turbo oil pump, new 20 thou oversized NA style race pistons to maintain compression, Linished and balanced rods, 1.2mm metal head gasket, all new gaskets, bearings and seals. block and head bathed and fully prepped, no turbo or exhaust manifold, can supply standard turbo manifold. Also has chrome harmonic balancer and water pump pulley and crank angle sensor bracket. Engine is not yet complete i still have to plug up the VVT and install pulley for the timing belt. I am happy to finish the engine before sale or you can buy as is.

Selling this engine as i no longer have the car it was for and i'm starting a new project.

$3500

I'm located in Newcastle

Link to comment
https://www.sau.com.au/forums/topic/105614-heaps-of-stuff-engines-parts-etc/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...