Jump to content
SAU Community

Recommended Posts

Guys,

Ive spoken to a few people and they recommend that I swap over to a D-Jetro for a couple of reasons the main one being throttle response and the cancellation of surge through the afm causing rich/stall conditions. I also just read the new HPI and it seems to confirm all these in a write up.

Does anyone here have any personal experience with them? Just to give you some background my engine specs are:

RB26 Head

Ported

HKS Cams and Gears

RB30 Bottom End

Forged Internals

Garrett T04Z Turbo

9.0:1 Comp Ratio

I aim for this setup to make approx 450awkw on pump.

Thanks for your input

Link to comment
https://www.sau.com.au/forums/topic/105765-apexi-fc-d-jetro/
Share on other sites

i would expect better throttle response on the airflow meter setup vs map sensor and the chuffing/shuffling usually occurs on twins that ive seen on the forum. the afm/stalling is usually also caused by incorrect bov setup

Ive spoken to a few people and they recommend that I swap over to a D-Jetro for a couple of reasons the main one being throttle response and the cancellation of surge through the afm causing rich/stall conditions

whoever gave you that advice i wouldnt go back to them for anymore of it :(

Everyone has a different opinion on the Power FC, whether to get AFM's or the D-Jetro version. I bit the bullet yesterday and order the D-Jetro, which has ended up costing me less than a normal PFC and 2 AFM's. I like the idea of MAP's over MAF's because of the stalling and messing with bov's (as said in below posts)

If you'd like to be turned away from the D-Jetro, read this :D

http://www.gtr.co.uk/forum/upload/showthre...?t=39859&page=1

^^but then the second last post gives the D-Jetro some hope, plus all of those guys know what they are talking about :wub:

MAP still works ok but if smooth street manners is your thing then stay with MAF.

I have been in a GTR on D-jetro. Response was awesome and street driveablity perfect.

My own car(S13) I swapped from a rom with Z32 to powerfc D-jetro. The car has never driven better. The responce of low throttle is fantastic. Also if I feather the throttle on and of in high revs(enough the bov goes) the car is not jerky like it was with the AFM.

Saying all this though means nothing, as we all should know by now an ECU is only as good as the tuner tuning it ......

whoever gave you that advice i wouldnt go back to them for anymore of it :D

Choosing a management system, I believe depends on who is going to be tuning your car. You could buy the best management system in the world but if your tuner has no idea about the system there is not much point.

It all comes down to which system your tuner is most experienced and comfortable with.

;) Adam :P

MAP sensor will always be difficult to tune at part throttle on a GTR due to the throttles being downstream of the sensor and so not really reading Manifold pressure. Can the Djetronic correct for throttle position against manifold pressure and react accordingly?

I was referring to the advice of the surging/rich/stalling

Thats not really ECU related and is incorrect information

Wasn't disagreeing with you. I was making an observation and further extending a train of thought.

If NissanFreak is using a certain tuner it is advisable to use the unit he/she recommends/ has the most experience with. (IMPO and others)

R31Nismoid, I'll give you an example.

I heard a reputable tuner say this first hand; he stated "you should not use a PFC with AFM on high mount twins". He gave good reasons why. But we all know there are plenty of GTR's around the world using the PFC unit (with AFM's) with high mount twin set ups.

Personally, I don't believe you can turn around and tell that tuner he is wrong. In his years of experience for a twin high mount set up he recommends a motec or autronic unit using MAP sensor.

*Just an example used has nothing to do with this thread. Just pointing out that differing opinions are not always incorrect*

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...