Jump to content
SAU Community

Recommended Posts

Hey Guys just wondering who is putting there hands up for the night cruise, details are as listed below;

When : the 2ND saturday in march (11thof March 2006)

Meetup at : Silver water park (off silverwater Road)

What time : Meetup 8:30pm for a 9oclock leave

Destination : Wollongong (Light House)

The more lines the better, looks like there will be around 50 cars to date, This is on behalf of PINK BITZ PERFORMANCE,

Post up your interest.

post-25017-1140690646.jpg

Edited by Gtr Glafche
Link to comment
https://www.sau.com.au/forums/topic/107045-night-cruise-to-wgong-light-house/
Share on other sites

Hidden message behind that photo Adrian?

Pink Bitz cruise - maybe... depends what time the dyno day finishes; there's about 50 cars going to that so I'm pretty sure people will want to do something.

$1000... and you can book the riveira for a day :P

The Riviera 33 , did you get the custom wood grain trim yet?

looking good so far guys, however i will do my very best to be there on saturday however , i may have work commitements.

That photo of the 34GTR , at 300km/h anf the driver suffered minor cuts and bruises. :O

I just remembered that the Dyno day is the same day

but hopefully everyone coming on the Dyno day end up coming to the cruise aswell. like Stan said. Well we will see on the day.. hope we can go on both but yeah.. :laugh:

i have a feeling those who dyno there car on the day would need to re-fuel again LOL

yeah i havent seen ya Joy like forever hope to see you and the gang on the day..

Laters



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...