Jump to content
SAU Community

Recommended Posts

Hey Guys just wondering who is putting there hands up for the night cruise, details are as listed below;

When : the 2ND saturday in march (11thof March 2006)

Meetup at : Silver water park (off silverwater Road)

What time : Meetup 8:30pm for a 9oclock leave

Destination : Wollongong (Light House)

The more lines the better, looks like there will be around 50 cars to date, This is on behalf of PINK BITZ PERFORMANCE,

Post up your interest.

post-25017-1140690646.jpg

Edited by Gtr Glafche
Link to comment
https://www.sau.com.au/forums/topic/107045-night-cruise-to-wgong-light-house/
Share on other sites

Hidden message behind that photo Adrian?

Pink Bitz cruise - maybe... depends what time the dyno day finishes; there's about 50 cars going to that so I'm pretty sure people will want to do something.

$1000... and you can book the riveira for a day :P

The Riviera 33 , did you get the custom wood grain trim yet?

looking good so far guys, however i will do my very best to be there on saturday however , i may have work commitements.

That photo of the 34GTR , at 300km/h anf the driver suffered minor cuts and bruises. :O

I just remembered that the Dyno day is the same day

but hopefully everyone coming on the Dyno day end up coming to the cruise aswell. like Stan said. Well we will see on the day.. hope we can go on both but yeah.. :laugh:

i have a feeling those who dyno there car on the day would need to re-fuel again LOL

yeah i havent seen ya Joy like forever hope to see you and the gang on the day..

Laters



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...