Jump to content
SAU Community

Recommended Posts

HKS T04R. $500 (needs bearings replaced) or $990 Fully Rebuilt by Garret or GCG in Sydney.

So if you are interested, you can buy it as is for $500, or fully rebuilt for $990. The choice is yours.

This turbo is good for around 600HP and is a great turbo for almost any application.

I also have a brand new stainless steel RB20/RB25 turbo manifold, never used, only $450.

Both the turbo and manifold are available now and wont last long, be quick first in to pay gets them.

post-23178-1141134717.gif

Sorry, i just replied to your pm about 5 minutes ago.

Here is a picture of the turbo, I forgot to mention it has a highly polished compressor housing, looks spectacular. As you can see, the manifold is brand new, polished, and looks great too.

Its not the best picture, but you can see the how good the quality of the manifold is, and how good the turbo looks.

Ok, here is the deal, I need to pay some bills tomorrow and I am flat broke, I think I have sold the manifold (waiting for payment) but the HKS T04R is still 100% available.

I will REDUCE the price of the HKS TO4R Turbo to only $400 if you can pay TONIGHT or before 11am tomorrow. Once off price of $400 for this turbo, need to sell it !!!! I will be online all night and will check back before i go to work in the morning. I need cash, someone might get a bargain tonight.

quicknissan.

If it turns out two people pay for the turbo then an immediate refund will be sent tommorow. This is a genuine sale, and I am not here to rip anyone off. So, i will check my bank account tomorrow and if more than one person payed it will be transferred back immediatly.

So, Turbo is sold pending payment, as is sold pending payment. I will reply here after work tomorrow with details.

quicknissan.

Looks like you'll be getting your cash back nismo33 - just spoke to him via sms and cause both manifold and turbo where purchased as a package - he can't really seperate...

Sorry mate.

I *do* however have a trust td06-17c here which was *going* to go on my car if you like? Bought less then a month ago, as a 'just recon'd, never used' turbo. So if you keen on that, give me a pm. Little bit more expensive then this one(not to much more), though, it's in perfect condition.

Ta.

Chris.

just spoke to the bank and managed to cancel the transfer,.. its all good now,. no worries.

thanks for the offer 510WW but im sort of looking for sumthin bigger than td06,.. if it were a td07 20g i might consider..its going in a supra.

thanks anyhow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...