Jump to content
SAU Community

A Bit Of Help With Fmic Installation

lingeringsoul

By lingeringsoul,
in Engines & Forced Induction

 Share

Recommended Posts

lingeringsoul Grand Master

lingeringsoul

Posted
Posted

Was just trial fitting the intercooler today (from JUST JAP) and found a few things I don't have answers for. The original pipe has a little nipple that comes out which is connected to the bleed valve/boost controller. If I take that piece off when I put the new pipe on, where is the boost controller gonna connect to?????.

The blue round things in from of the radiator...........would that be the horn?? if so, why are there two of them??

Lastly, big long pipe that goes over the fan, it has a piece of metal coming out with two holes that seems to connect to the two holes on the engine but when I trial fitted on, they don't seem to match up no matter how hard I try.

If anyone has some detail pic or info of their front mount install for a Series 2 GTST please help me out.

mid life crisis Veteran

mid life crisis

Posted
Posted
Was just trial fitting the intercooler today (from JUST JAP) and found a few things I don't have answers for. The original pipe has a little nipple that comes out which is connected to the bleed valve/boost controller. If I take that piece off when I put the new pipe on, where is the boost controller gonna connect to?????.

The blue round things in from of the radiator...........would that be the horn?? if so, why are there two of them??

Lastly, big long pipe that goes over the fan, it has a piece of metal coming out with two holes that seems to connect to the two holes on the engine but when I trial fitted on, they don't seem to match up no matter how hard I try.

If anyone has some detail pic or info of their front mount install for a Series 2 GTST please help me out.

i had the some problem fitting one last week into my sons car o made a bracket that bolts to that flat bit plate and then onto the engine bracket i had to make new brackets for the intercooler as well as the supplied ones didnt quite line up. also the clamps supplied are a bloody tight fit and caused some grief as well my kit wasent from just jap tho it was a geniune hybrid hope the pic helps . btw the horns just undo them and mount them inside the engine bay next to the rad

sorry about posting the same pic twice here is the 2nd pic i ment to post

mid life crisis Veteran

mid life crisis

Posted
Posted (edited)

yep i have a photo where the hole goes but all it shows is the pilot hole for the centre of the holesaw btw the hose from the boost controller i just brought a t piece and connected it the line that comes out of the plenum to the fuel regulater seems to work ok not causing any hassles

Edited by mid life crisis
lingeringsoul Grand Master

lingeringsoul

Posted
  • Author
Posted

do you have to relocate the washer bottle at all?

you wouldn't happen to have a picture of the hole from the engine bay would u? so I could get a rough idea where to drill the hole.

mid life crisis Veteran

mid life crisis

Posted
Posted
do you have to relocate the washer bottle at all?

you wouldn't happen to have a picture of the hole from the engine bay would u? so I could get a rough idea where to drill the hole.

mate i didnt even remove the bottle when i drilled the hole the hybrid kit come with picturesand measurments for the hole give me ya email addy and i will pass on the instructions to ya
Savage Bliss Proficient

Savage Bliss

Posted
Posted

You'll prob find the cooler was made for an RB20 as the holes will match up no worries on the side of it. You can suvive without this part attached... I have mates who have just broken it off!!

mid life crisis Veteran

mid life crisis

Posted
Posted

i would rather spend 10 mins making a bracket than just to rip it off and have a lump of broken weld stuck on the pipe let alone taking the chance of tearing a hole in the pipe while ya just rip it off

wraith_skyline Proficient

wraith_skyline

Posted
Posted

I got a hybrid kit and it said to trim the fan to make the top pipe fit, i also remade the cooler mounts to make it easier to fit. Then i missed when i drilled the hole and made a bit of a mess, but that should be repaired asap

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...