Jump to content
SAU Community

Recommended Posts

hey guys i've had enough. car's for sale. $15,000 firm no rego no rwc.

vehicle is:

1991 Nissan 180sx black in colour.

Engine: Arias 40 thou oversized forged pistons (has 1200 k's on the motor total) new timing chain and oil pump water pump and thermostat

Scat I-beam rods

Clevite race bearings with standard crank machined to match

O-ringed block

tripple layer metal head gasket

Tomei rocker stopper kit

ARP - rod bolts, head stud kit, bearing retainer kit etc....

ported and flowed head ----------- REBUILD COST ME $8,000

450cc gtr injectors in custom railrising rate fuel pressure regulator

Greddy drift sump

cusco catch can

cusco coil overs (HEIGHT ADJUSTABLE)

5 puck custom clutch

five stud conversion wiith sumitomo front 4-spot calipers

290mm slotted and cross drilled rotors

front camber tops

safety 21 half cage

G REDDY T518z turbo with custom flowing on the front cover.

Trust GTR style intercooler with custom powder coated piping - blue

all hose clamps are high pressure truck type clamps, with new silicone joints.

x-force extractors (stainless)

trust front front pipe

x-force dump pipe

x-force cat back 3-5 inch exhaust.

fixed position drivers seat

nardi steering wheel

razo pedals

hks turbo timer

Turbo smart eboost 1

r32 gtst rims and second hand tyres - its a drift car dammit

type x front bar - f**ked

NIsmo side skirts -

******* one door is in primer at the moment can and will paint on request.

if you respray the vehicle and do some other tidying up = instant show car/drift car

Vehicle has a total of 101,000 k's on the chasis.

estimated power somewhere between 350 - 400hp at the wheels on 19 psi

call Shauno on 0424534691 or

also have a power fc and hand controller for the vehcile as well not fitted and not included but can be purchased seperatly for $1,100.

Also have 18 x 8.5 and 18 x 9.5 inch star corp racing wheels slight drift damage to one, completly rooted tyres on these. $1000

plus i have assorted rear trim parts if you want them you can have those

sorry i don't have any photos on me at the moment

Link to comment
https://www.sau.com.au/forums/topic/108780-cheap-bombed-180sx/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...