Jump to content
SAU Community

Recommended Posts

Guys

I have these turbos for sale. Only been on the car for about 5000 kms.

Made somewhere around the 300awkw at just under 1.3 bar.

Im after $2000 ono. No shaft play at all. These are like brand new.

Reason for sale? Need funds to buy a 34 gtr

Pics are below

post-8082-1142655855.jpg

post-8082-1142655915.jpg

post-8082-1142655954.jpg

Just checked the garrett website.

These turbos are rated at 360hp by garrett EACH

Which means they are good for around the 650hp mark @ 1.6 -1.8 bar

http://www.turbobygarrett.com/turbobygarre...0R_707160_5.htm

Reason for sale? Need funds to buy a 34 gtr
Need money for a house deposit. These are going back up to the top

so why are you selling them?...........................

By the way, which turbos are you selling? The Garrett Gt2860r or GT2560r, they are two different turbos

need to buy a gtr34 so i need the money haha

need to buy a house so need it for the deposit haha

big difference champ....

if you have money to waste on a r34gtr before your house and sorting that out pfff no idea.

i think you should tTHINK about things more...car and house wise??

and also your post on why you want to selll hahahaha

thought this was so funny..

maybe you want a bigger house so just try to sell them for 3grand hahaha

Sorry guys

I actually wanted to do both ?

Call me confused, but I think I can only have one or the other.

The real reason is that I am selling my gtr, so i really dont need these. I will have larger turbos on the 34 seeing as the motor will be having certain modifications done to it :)

These modifications will also require larger than 700cc injectors. That is all im saying for the moment. I NEED money :mellow:

the turbos are these ones

http://www.turbobygarrett.com/turbobygarre...0R_707160_5.htm

  • 1 month later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...