Jump to content
SAU Community

Recommended Posts

Hey Guys,

Everyone Been good help on here so far and got me through,

This time I have tryed so much and no luck so far.

My R33 drops idle intermitently and then cuts out, on idle or even driving.

The car seems to drive fine then jsut looses power and then drops to low idle and drops out, then comes back after bout 20 seconds.

I have replace :

1 Fuel filter

2 spark plugs

3 o2 sensor(with a new 3 inch dump pipe.)

I starting to run out of ideas.

I had a performance company lookat it and they new crap all. i won't mention the company name yet.

I thinking all that left maybe be fuel pump or somthing.

It only happens everynow and then, and is now happening more often.

I have minimal mods. basily increased boost the biggest.

Anyone have any ideas please let me know.

I to the point where i might have to get a machanice with a diagnistics system look at it.

Any help or ideas is a help.

It starting to cost me too much,

Thanks Rob :(

:(

Sounds like what my old vl did. Ended up being the crank angle sensor. Just a stab in dark.

Thanks mate, any feed back good feed back,

Could be, wat the crank angle sensor do, and how much to fix that u recon ??

Thanks dude

Robz

:)

It's a distinct possibility, but I would have thought u'd have trouble throughout the rev range too if it was the CAS, however depending which 1 of the two reference signals is dying you may get away with a few extra revs. If the other dies though, u'll have nothing. Is it happening more when it's hot or on a hot day out of curiousity?

It's a distinct possibility, but I would have thought u'd have trouble throughout the rev range too if it was the CAS, however depending which 1 of the two reference signals is dying you may get away with a few extra revs. If the other dies though, u'll have nothing. Is it happening more when it's hot or on a hot day out of curiousity?

Hey Electro, well it mainly happens after a drive after it has warmed up, or more when i have given it to her, less likley to do it if i go real easy,

so yer coudl be wat u thinking, it has a los of power over normal rev ranges too, it not like it ment to be, that wat i getting at, i always throught it was fuel or air related, so i minimissed that and done wat i can, so looks like could be some sensor.

any more info/input is all good,

thanks mate

:P

Starting to sound like a pretty good chance that's ur problem. Also if you shut it off for a few minutes to heat soak & then try to start it again but have trouble then I'd place very high odds on it.

It's usually under heat that they fail, & sometimes it is intermittent, electronics & heat are a real pain when combined.

If you're worried that you are going to waste ur money on a new sensor though, take it to a deacent auto elec that specialises in EFI technology & make sure he has all the equipement (IE occilloscope and diagnosics equipment to plug into the ECU) and make sure he know's what he's talking about. If he doesn't have any knowledge of Nissan CAS being a problem then run.

hey guys,

thanks for all the input, i today have just taken to northside EFI at brendale, and he got all teh gear to test it, i told him wat i have done and explained wat u guys recon it could be.

hoping he will find and won't cost me the earth.

:( heaps hey

rob

:P Hye guys,

Problem at conclusion and all solved now.

My mechanice who did the best job( Ron at Northside EFI at Brendale)

found that is was the Air Flow Meter, and my fuel pump was playing up too, not holding presure.

So the main problem being teh AMF, i sorced one down second hand, from Driftking at Geebung for mad price. put on tonight and the car goes harder and better that before.

Thanks everyone for your help.

I have spend some money on it, but i got there, got a car full of new components now.

Cruise on boys

Thanks

Robz

Cool good to see u got it soughted out. I had forgotten that the AFM is a common problem with 33's. Reckon I'll be getting a Power FC & pissing off my AFM all together if it starts giving problems on mine. Will replace it with a MAP sensor.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...