Jump to content
SAU Community

Recommended Posts

Ive got a R32 GTR and ive taken out the ristrictor in the hose that goes to the boost controller solaniod but i was also told to join those 2 hoses together to get 15psi.. It works BUT like at 6000rpm its sometimes starts to make a limiter noise. could some one help me because my car is GOIN NUTS ON 15PSI :O

I was only running about 8-9psi before but now that little bit extra is awesome.

DO GTRS have a boost cut defender?

ANYONE?

Im only new to the forum so this is a pic of my car.

post-26787-1143156584.jpg

explain exactly what happens at this 6000rpm mark.

does it cut the power completely.. like is it violent?

is it like a rev limiter where it stutters and kinda back fires?

doest it keep reving up but kinda misses?

what happens to the boost gauge when this "CUT" happens? still sit at 15 or drop?

with more description and those answered, people can give you a better response as to what the problem is.

at the moment it could be..

AFM max

spark blowing out due to excess boost.

coil packs arc'ing out

etc...

I think that the fact that you now have about 2 x the boost you had before, you are blowing out the spark.

there are a few things you can try which will cost you nothing but some of your time.

1.) take out your spark plugs and gap them down to 0.8mm.

if they already are, drop them back to 0.7mm.

2.) with some electrical tape, tape up the coil packs. there is a guide on this in the maintenance section of these forums.

I did the above 2 points 2 weeks ago and my car revs out smoothly now.

mine is an rb20 but same edal.

runs a little more boost than stock.

I suggest you try the 2 things above as they are free and MAY fix the issue.

If you are in Sydney, I can help you do it if you like.

if they are anything like GTST's then yes they do.

Write it out 20 times..........

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

Half way there……………

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

THERE IS NO SUCH THING AS BOOST CUT

Hope you learnt a lesson, next time it will be detention for you

:O cheers :P

if you are running 15psi and stock ecu you will be encountering the STOCK EXCESS AIRFLOW protection. turn the boost down and try again, i would suggest around 10psi at the most. this should work around the excess airflow protection

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I certainly fall into the annoyed camp, but glad to hear that if it's happening at low boost then I'm not likely going to blow a turbo and end up with metal shards in my oil. Just feels like it prevents me from really driving it without hesitation and "peak" performance. Wonder if it's the VCAM, it did an impressive job of shifting the torque curve and faster spool, but maybe now it's "too fast" and there's too much air for how open the throttle is.  Based on some other threads, will also do some reading on synchronizing the actuators. They are the default actuators that come on the Garrett's and I would think they would be set the same coming from the factory, but if the turbos don't actually work exactly the same way at the same time as previously mentioned, it would be worth making sure the actuators are actuating together properly
    • I went down this rabbit hole before, ended up sourcing a motor from the UK (I'm in Japan) which also didn't function correctly. With the original motor, I disassembled it and reassembled it and it works somewhat, sometimes. What I could deduce from all my screwing around is that there is calibration of the gears on the inside of the motor and two ramps on the main gear which activate switches that operate the motor and move the sunroof either to retract into the roof or tilt. Where I got stuck was that, it seemed in my case that one or both of the switches that are activated by the ramp on the gear did not always activate and thus the motor did not move, causing it to sometimes not retract or tilt (apologies, I've forgotten which way it didn't work.).  Of course this part is discontinued at Nissan now, it's the same part in the S15 but no other models. I also contacted the manufacturer of the component for schematics - forgot the name, they're based in Gifu - but they declined to share the information due to being bound by an NDA, sadly. Looking through my pictures now, it seems I last had a crack at this in 2022. See, I so kindly wrote "open" and "close" next to the switches. If you figure it out, please do tell me. Those little switches, with the red buttons may need to be replaced.
    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
×
×
  • Create New...