Jump to content
SAU Community

Recommended Posts

if anyone has a S1 33 AFM (4 pin, green label) i can borrow *right now* or latest tomorrow,

give me a call/sms on 0405 908 860

will give a carton for their troubles :D

cheers!

Hey Mitchy,

Do you still need the AFM? mine is a 94 s1 at Hyperdrive at the moment getting replaced with a Z32 and other stuff. I am pretty sure you would be able to speak to Ken and get it from him...

Cheers

JB

Hey Mitchy,

Do you still need the AFM? mine is a 94 s1 at Hyperdrive at the moment getting replaced with a Z32 and other stuff. I am pretty sure you would be able to speak to Ken and get it from him...

Cheers

JB

cool.

are you looking to sell it?

i pretty much need to buy one.

i bought one before, not realising it was for the S2, and i tried wiring it in according to an r33 manual i have, but the car still stutters, soi i want to see if the S1 afm works, and then buy one :huh:

cheers

mitch

cool.

are you looking to sell it?

i pretty much need to buy one.

i bought one before, not realising it was for the S2, and i tried wiring it in according to an r33 manual i have, but the car still stutters, soi i want to see if the S1 afm works, and then buy one :huh:

cheers

mitch

Yeah...I have no use for it anymore :)

Try it and see if it fixes the stutters...if it does cool...if not you might have other problems :) You will have to ask Ken for it. Hyperdrive is doing all of the work for me while I am in London, but if you are going on the April cruise I will see you there :)

Cheers

JB

picked up the AFM today... it works!!

thanks JB :)

No Worries :) Ken told me you dropped it back. When the Z32 arrives, I will let you know if will still need one by then. I will be back in Perth for the April cruize if u will be going :(

JB

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...