Jump to content
SAU Community

Recommended Posts

l bought a 87 s2 5sp silhouette for a song good condiction too goes like a bat out of hell but when l sit and idel the temp rises right up is this normal for them or is there a problem seeing that most of you have owned one or two in your life time you might know , and this is my first one any help or sugest would do driving is fine just when l sit and idle regards james

Link to comment
https://www.sau.com.au/forums/topic/111553-silhouette/
Share on other sites

l bought a 87 s2 5sp silhouette for a song good condiction too goes like a bat out of hell but when l sit and idel the temp rises right up is this normal for them or is there a problem seeing that most of you have owned one or two in your life time you might know , and this is my first one any help or sugest would do driving is fine just when l sit and idle regards james

I've had an 87 Silh for years. Temp gauge has always sat about 1/2 way on the gauge, going a little higher in high temps using the aircon. Temp rising in the way you describe is not normal. Check and cleaning cooling system, particularly radiator. Check thermostat and another possibility is water pump on its last legs.

Link to comment
https://www.sau.com.au/forums/topic/111553-silhouette/#findComment-2058277
Share on other sites

my temp gauge (when working)sat at about 1/3 all the time,

SteveL, i'd say your right on the money with your surggestions, a good cooling system flush about $20, may be replace the water pump if the flush dosent help, good coolant is another thing too..

Link to comment
https://www.sau.com.au/forums/topic/111553-silhouette/#findComment-2060270
Share on other sites

I've had an 87 Silh for years. Temp gauge has always sat about 1/2 way on the gauge, going a little higher in high temps using the aircon. Temp rising in the way you describe is not normal. Check and cleaning cooling system, particularly radiator. Check thermostat and another possibility is water pump on its last legs.

thx 4 the info steve will try what you said and let you know :D

Link to comment
https://www.sau.com.au/forums/topic/111553-silhouette/#findComment-2060545
Share on other sites

What about the thermo fan? Is it a clutch type (as in it is attached to the pulley where the water pump is, but can be turned by hand), or is it an electric one (mounted to the radiator)?

It sounds to me like you have fan issues, particularly if the car is fine when moving (air is flowing through the radiator).

My DR has a temp sensor in the bottom tank of the radiator, and that kicked in the electric fans. Unfortunately, the temp sensor stopped sensing, so the fans never came on! When driving, my temp was rock-solid, but as soon as I sat idling, it would climb and climb and climb and...well, you get the idea.

Link to comment
https://www.sau.com.au/forums/topic/111553-silhouette/#findComment-2061069
Share on other sites

What about the thermo fan? Is it a clutch type (as in it is attached to the pulley where the water pump is, but can be turned by hand), or is it an electric one (mounted to the radiator)?

It sounds to me like you have fan issues, particularly if the car is fine when moving (air is flowing through the radiator).

My DR has a temp sensor in the bottom tank of the radiator, and that kicked in the electric fans. Unfortunately, the temp sensor stopped sensing, so the fans never came on! When driving, my temp was rock-solid, but as soon as I sat idling, it would climb and climb and climb and...well, you get the idea.

its a clutch fan type and for it to stop altogether the pump would have to have siezed or the fan belt snapped? you'd notice this as soon as you open the bonnet with the engine running..

Link to comment
https://www.sau.com.au/forums/topic/111553-silhouette/#findComment-2061653
Share on other sites

If the clutch (in the fan) is on it's way out, it could cause the problem too. When the engine is idling, the fan should be rotating at about 1:1 with the crankshaft pulley. If the fan is going slower (particularly much slower) then it could be the culprit. With the engine stopped, spin the fan with your hand. There should be a little resistance in it.

Is the fan shroud missing / been removed? Is it using water?

Edited by Matty T
Link to comment
https://www.sau.com.au/forums/topic/111553-silhouette/#findComment-2062439
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • R34DE as in R34 with an RB25DE? So did you get this? Or you planning to?  I'm not really sure what you're saying. 
    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
×
×
  • Create New...