Jump to content
SAU Community

Recommended Posts

The reason my car uses heaps of fuel is because of lowish gearing, at 100km/h it sits at 3000rpm and is boosting at that level, its good to have that sort of power on tap but I dont need it really for normal driving.

I've been pondering this dilema for some time now.

I could get a bigger turbo that has more lag and people with these say if they drive sensible they can get good milage, but no bottom end and large outlay.

Now if I could stop boost (run NA using standard BOV) to 3500 I could have the best of both. To do this I would need a soleniod that cuts in/out at 3500 (or 3200 etc) for when I'm doing a long trip.

The BOV would also have to work normally and is pos if I have another solenoid that activates the first.

I'm using the MAF based Microtech so I hope its possible.

Link to comment
https://www.sau.com.au/forums/topic/111900-3500-rpm/
Share on other sites

boost doesnt use fuel or affect your economy. the economy is driven by rpm and airflow meter load. airflow meter reads more air, the fuel cells drop a little on the map and it will use more. there is more to your problem than you are thinking of. upgrading the turbo is a pointless exercise. boost does not affect your fuel economy, airflow and revs do.

so whats your fuel economy like? mine sits at 3000 at 100km/h and i can get 600k's to a full tank on the highway or around 400k's city driving with some mild high powered runs.

Link to comment
https://www.sau.com.au/forums/topic/111900-3500-rpm/#findComment-2063944
Share on other sites

ah crap i just read your using a microtech. well is it tuned properly? what the afr's like on cruise/low load? or is it just max power tune?

does it support 02 feedback? if not then dont bother replacing the 02 sensor as its not used.

your likely reasons for bad economy (based on microtech)

- light load / cruise map area is not tuned and runs default map values ie: most likely mega rich

- microtech doesnt support closed loop / 02 feedback

- if ecu suppports 02 feedback / closed loop then 02 sensor is dead

get back to me regarding those

Link to comment
https://www.sau.com.au/forums/topic/111900-3500-rpm/#findComment-2063951
Share on other sites

if you do find out microtech doesnt support closed loop / 02 feedback you can still get good economy it just takes a lot longer to tune and fixen up. my powerfc is tuned with 02 feedback off and im getting the economy i posted above. so if thats the case, you need to have your car tuned on the road with a wideband sensor. basically drive around some local suburbs at normal speeds (and normal load) and tune around that. theres no need to do any max power, full throttle runs.

ie:

cruise at 30km/h in 3rd gear

cruise at 40km/h in 4th gear

cruise at 20km/h in 2nd gear

cruise at 60km/h in 5th gear

do those sort of road tuning 'areas' on the map and that should sort out most of the light load / low cruise areas.

Link to comment
https://www.sau.com.au/forums/topic/111900-3500-rpm/#findComment-2063959
Share on other sites

Thats interesting I thought that as the MAF saw more pressure it increased fuel etc to accomdate, the boost gauge on the microtesh dash unit shows boost at 3000 and assumed it would be compensating.

I recently had a problem with ignition and havent checked usage, but I was getting 10km/l and it was down to 8 before I fixed it. I specified an economic tune as it was daily driver.

Thanks for your replies Paul but the question was Is it possible? but youv'e cleared the practicle side.

QUOTE(R33S2 @ 10 Jan 2006, 08:04 PM)

Hey Dan

I was talking to you about turbos and fuel consumption last thursday and how my car sits on boost at 100+ km/hr and never got to ask if there is a compatiable turbo that wouldn't see boost till 3500rpm or so, I haven't got a clue if this is a good idea or not but am interested to hear your opinion.

Well , funny thing is my highway mileage is friggin awesome. I get around 750k's to a tank on the highway....but only 350-400 around town. I can drive along in 4th gear at 100 and still not be on boost lol.

Link to comment
https://www.sau.com.au/forums/topic/111900-3500-rpm/#findComment-2064025
Share on other sites

the ecu (stock or microtech) has no elec map sensor (pressure sensor) so all it does is measure air coming into the engine. whilst if it measures more air coming it will use more fuel, it wont measure pressure (ie: boost) so you can have 12psi or 2psi in the manifold and it wont matter, all the ecu cares about is how much air is coming in.

an ecu such as powerfc djetro which is a map sensor ecu uses a map sensor instead of an airflow meter and guesses how much air is coming in based on pressure

it just sounds like your right foot is the main culprit. get a friend to plod around in your car for a few days, you may be surprised about the economy you get if someone else drives it

Link to comment
https://www.sau.com.au/forums/topic/111900-3500-rpm/#findComment-2064866
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...