Jump to content
SAU Community

Recommended Posts

R33 series 1 gtst with 3ltr Rb30 bottom end (instead of 2.5ltr) Motor done approx 15000km

Located near Gosford NSW

**has 12 months Rego***

Details

*RB30 block

*Arias Forged Pistons (20 tho oversize)

*Shotpeened rods

*ARP rod bolts

*New rod Little end bushes

*New ACL main and big end bearings

*Mild Head port and polish + full head service

*3 layer metal head gasket

*all new gaskets, seals, welsh plugs etc

*Custom oil catch can and breather

*Garrett GT35/40 dual roller bearing turbo

*Xforce high mount stainless exhaust manifold

*50mm external waste gate and screamer pipe

*3 inch exhaust turbo to cat with 3 inch cat. 3.25in cat back with stainless Jasma rear muffler.

*Custom inlet Plenum and EF falcon throtle body

*Hybrid bar and plate intercooler

*Turbo smart type3 blow off valve

*NOS brand nitrous fogger kit and bottle

*600cc injectors

*Bosch 044 external fuel pump

*Custom 1.5ltr surge tank

*Walbro high flow intank pump

*malpassi fuel pressure reg

*Wolf3d engine management

*Apexi electronic boost controller

*PLX Wide Band air/fuel ratio meter with gsensor and laptop data logging

*Xtreme extra heavy duty 5 puck ceramic button clutch (1200kg pressure plate)

*19 inch zenetti kaotic rims 19x9.5 (265/30/19) rear and 19x8.5 (235/35/19) front

*KYB lowered springs and shocks

*White line rear camber kits

*GREDDY electronic boost gauge with recall and warning light

*GREDDY electronic oil temp gauge

*GREDDY turbo timer

*TRUST short shifter kit and knob

*Pioneer cd/mp3 player

*Pioneer front splits and custom door pods

*Pioneer rear 6 inch speakers and custom parcel shelf

*Sony explode 12 inch sub and box (sub damaged but still works fine)

*Boss 4x75wrms amp

Car has produced 301kw (403hp) at the rear wheels on 18psi, will make more with more boost. Set of cams and larger exhaust housing will see 350+ Has done a 12.1@ 118mph on a 39degree day with lower boost and no NOS. Should Do high to mid 11 on cooler night without nos and mid to low 11 with NOS Email or ring with any question [email protected]

Asking $25,000 or best offer

0422802102 Ask for scott

post-10986-1144030543.jpg

post-10986-1144030668.jpg

post-10986-1144030695.jpg

post-10986-1144030731.jpg

post-10986-1144030772.jpg

post-10986-1144030825.jpg

post-10986-1144030851.jpg

post-10986-1144030877.jpg

post-10986-1144030908.jpg

post-10986-1144030938.jpg

post-10986-1144031257.jpg

Edited by OFENSV

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...