Jump to content
SAU Community

R33 Thermostat


Recommended Posts

Guy's follow the bottom radiator hose up to where it joins the motor,,,thats the stat cover,,,3 bolts from memory.

The stat is the same as a VL 3.0L,,,Nissan Part No is 21200-42L05 and it fits all R33's.

Neil.

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-195749
Share on other sites

  • 6 years later...

ok guys, there are a few things to know here:

firstly for the money and time saving just get a genuine nissan one from nissan parts. they are around $50-60.

second, if you want a 'tridon' one...the part number is TT268-170. this is the 77deg one. there is an 85 deg one...dont get this!

lastly if you want to waste money, get the nismo one but these are over $100 if not closer to $150 and open at 67 or so deg.

you will also need gasket goo for this as there is not a norml gasket there. i use the blue stuff...works perfect!

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-4606827
Share on other sites

bellow i attached instructions from the RB engine manual.

view order 3 then 1 then 2. (sorry i didnt rename)

as the above people have said use either the tridon or stnd nissan one.

tridon will set you back about $28 and its one of the good cheapies.

make sure the jiggle pin is pointing to the top of the motor.

for gasket sealent i recomend a product from loctight.

Its a silicone based gasket goo, its loctight blue something or other.

It's the ducks nuts, will come in handy down the track to.

let us know how you go.

post-55273-1242824646_thumb.jpg

post-55273-1242824666_thumb.jpg

post-55273-1242824704_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-4606908
Share on other sites

was reading a thread recently and a workshop operator said he'd been through a bunch of tridon thermostats that were crap, and caused problems.

just use the nissan one. also there is no reason to use a lower temperature it will NOT help you, it just means your car won't get up to temp and you'll lose fuel efficiency.

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-4608777
Share on other sites

  • 2 years later...

hi guys on my r33 gtst 1993 it has a braided cable that runs down threw the chassis and comes out next to the exhaust, and theres something that attaches to that which im not sure what it is or where to get another one because i scraped going over a speed hump and its pulled it out and stuffed it and i think its shorting out, my thermostat light is staying on and check engine also comes on itermitently. Any help on where i can get another one of these, and or what it is would be good cheers

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-6110663
Share on other sites

  • 2 years later...
hi guys on my r33 gtst 1993 it has a braided cable that runs down threw the chassis and comes out next to the exhaust, and theres something that attaches to that which im not sure what it is or where to get another one because i scraped going over a speed hump and its pulled it out and stuffed it and i think its shorting out, my thermostat light is staying on and check engine also comes on itermitently. Any help on where i can get another one of these, and or what it is would be good cheers

Disconnect it, it's useless. Pull out your passenger seat and delete that sensor

Link to comment
https://www.sau.com.au/forums/topic/11244-r33-thermostat/#findComment-7274366
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...