Jump to content
SAU Community

R32 Gts-t Landing Soon. What To Expect?

r32monster
 Share

Recommended Posts

r32monster Newbie

r32monster

Posted
Posted

Hey there,

Ive made a deposit and my R32 is coming soon! Check it out below:

R32 GTS-T

I was wondering, as this will be my first "performance" car, what I should expect. Ive driven my friends and its an awesome ride from what Ive experienced. But what I want to know, is what to do and what not to do when I get it?

Like, new fuel, driving hard, or any other things I should be aware of?

Thanks guys.

sammus Grand Master

sammus

Posted
Posted

expect a fun and easy to drive car with f**kall low end torque that steers like a trolley when you go faster than 80 and that you'll get bored of and spend thousands of dollars on to go faster and get pushed into the seat to a higher degree later on. :)

dezz Grand Master

dezz

Posted
Posted

seriously though...

might wanna get timing belt, water pump and all the other shit under the cam cover done while its being complied... it will be bone dry fuel wise, so make sure you fill up with premium 98 RON etc....

i got ALL my oils done at compliance, diff, gearbox and all that...my car runs sweet has, have not had 1 issue with it yet...didnt change spark plugs or anything yet and it runs beautifully :)

MFC05 Experienced

MFC05

Posted
Posted

The battary will most likely to be flat and tires will mostly likely to be bold so be prepare to add these cost in look out for any bodywork damage that wasnt on the pictures and get a service done and check to see if anything need to be replaced take it for it drive and see if runs smoothly cause the car would be being sitting in Japan for while, these are the things i would do hope it helps

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...