Jump to content
SAU Community

Gt-r's U.s. Nameplate Announced

Alfadog

By Alfadog,
in R35 GTR

 Share

Recommended Posts

Alfadog Collaborator

Alfadog

Posted
Posted

Received this via e-mail today from NISSAN.

Since the unveiling of the GT-R PROTO at last October's Tokyo Motor Show, Nissan has continued development of the legendary GT-R sports coupe. And while details about the next generation GT-R have been few, one important piece of information was made public today.

Mr. Carlos Ghosn, President and CEO of Nissan Motor Co., Ltd., kicked-off the New York International Auto Show with the exciting revelation that the GT-R will be sold in the U.S. as the Nissan GT-R.

As part of his keynote address at the International Motor Press Association Breakfast, Mr. Ghosn said that when he unveiled the GT-R PROTO, Nissan had not yet decided whether the GT-R would be sold as a Nissan or an Infiniti in the United States.

Mr. Ghosn also expressed enthusiasm that the heart-pounding GT-R will build on drivers' passion for the Nissan brand.

This communication is first in a series leading up to the launch of the Nissan GT-R. As part of an exclusive group, you will be among the first to receive information and special insights into the development of the Nissan GT-R.

©2006 Nissan Motor Co., Ltd.

So straight from the horses mouth, it will NOT be an Infiniti. I can understand it not being named Skyline in the States too since the "standard" Skylines aren't Skylines either... but I still think they should be named Skyline GT-R in Japan etc.

Anyway, info FWIW.

Link to comment
https://www.sau.com.au/forums/topic/113440-gt-rs-us-nameplate-announced/
Share on other sites
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • MBS206
      Rear subframe stay bracket bolt removal issues

      By MBS206 · Posted

      TBH, it sounds like the threads on the bolt are fubar in a specific section. Most likely as you've been working it back and forth it has torn threads out, as you loosen the bolt, this section enters the nut, now you're spinning a round shaft inside the nut, there's no threads here.   Use something similar to a claw on a hammer that will fit either side of the bolt head and try to apply downward force while also undoing it. The idea is to attempt to catch a thread, or just rip the f**ker out. Caution on ripping out, as it could bend/maime/mangle what the captive nut attaches to. If the captive nut is actually okay, you could do the dirty part of cutting the head off the bolt, then cut a slit in the end of the thread that's now exposed and then screw it up and into the area the captive nut is until it falls out the other side. However, this does risk the remainder of the bolt rusting over time and damaging near the captive nut and also making it rust. However, so can cutting pieces of panel work out to access this area if you don't reseal it properly.
    • MBS206
      Rb25 det nitto washer crank gear

      By MBS206 · Posted

      Well, every piece of information on that part when you track it back to Nitto says it's for a KIT of theirs. It is also designed thicker to be stronger. And they speak about a specific harmonic balancer bolt they supply for the whole setup.
    • MrStabby
      Rear subframe stay bracket bolt removal issues

      By MrStabby · Posted

      Techniques for removing stuck bolts are: hitting the bolt head with a hammer, heating the bolt to red hot then letting it cool and working it back and forth like you are already doing. AFAIK the idea is to try to crush whatever material is stuck between the threads (and heat also melts locktite but that's almost certainly not relevant in this case).
    • GTSBoy
      Rb25 det nitto washer crank gear

      By GTSBoy · Posted

      Yuh, I think it works with the Nitto gear only. I presume that you're not also using the Nitto gear? Watch the video. Compare the interface between the Nitto gear and washer (on the gear side) vs the stocker and decide if you think the Nitto gear is different from stock there.
    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Liking the new charger, battery all good (I think).   Also like how you can put it in power supply mode too. Will troubleshoot with that sometime soon.
×
×
  • Create New...