Jump to content
SAU Community

Recommended Posts

I have almost completed my rebuild of my 32 gtr, it is sitting on the hoist at the moment and i am scratching my head as to where the so called "air bleed plug" that the service manual says to pull out to get constant hydraulic pressure to bleed the 4wd is, i have searched in the boot and under the car to no luck, if someone could point me to where it would be that would be great, the manual says "lower dash side" on the location and the plug is supposed to be white or something, thanks!

Link to comment
https://www.sau.com.au/forums/topic/113825-attessa-4wd-help-plz-bleeding/
Share on other sites

I have almost completed my rebuild of my 32 gtr, it is sitting on the hoist at the moment and i am scratching my head as to where the so called "air bleed plug" that the service manual says to pull out to get constant hydraulic pressure to bleed the 4wd is, i have searched in the boot and under the car to no luck, if someone could point me to where it would be that would be great, the manual says "lower dash side" on the location and the plug is supposed to be white or something, thanks!

Its a white connector behind the driver kick panel next to the accelerator pedal.

you don't need to worry about the white plug....just put the car up on stands, start the car in neutral....anytime the engine is running there is pressure in the attesa system.

then there are 2 bleeders, one at the rear of the transfer case and another bastard above the rear drive shafts.

The bleeding is dead simple, easier than brakes because the fluid is under pressure.

Make sure the resoviour in the boot is full, then with time the motor is running, put a piece of clear pipe over the bleeder (same as brake line) and open the bleeder. Let the fluid come out until there are no bubbles. Do it up again.

See....easy :D

<bump>

I wanna bleed the attessa in my car. It doesn't look terribly complicated, but I would *really* appreciate a couple of pics in a "howto" thread.

Oh - make sure you include a suggestion (or three) about appropriate replacement fluid.

I just don't quite have the confidence to try it without pics.

Thanks

nK

nicholas Krul

No worries, ill do the DIY when i have the car at my mechanics, which will be very soon as i have to have it ready for a track day on the 29th of this month

Ill take loads of pics for you and the other guys who feel the same way

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...