Jump to content
SAU Community

Recommended Posts

I have reason to believe that one shop has .

Trouble is that there must be atm new emission evidence or original evidence ( not photocopied ) for the GTR's.

As the only 4wd emission dyno is at the EPA in Melbourne ( I think ) and it has to do a 24 hr emission cycle it would probably cost a small house in sydney type price to do it.

There is talk of allowing them to run in 2 wd but is just talk atm.

Cheers

ken

Oh and May 8th is cutoff. All vehicles must have the paperwork signed off ( but not necessarily plate issued ) by that date or you now own a race car.

The new scheme started in May 2002 and overlaps the old scheme until it ends in May this year - but to comply cars under the old scheme you have to have them finished before May, so that means shipped out of Japan within about 2 weeks maximum.

just got an import approval prob for the last car getting under old scheme. I'd say if you want to get a car have to do it by the 15th March or so. All vehicles must be plated under the old scheme by the 7th May 2003. Import Approvals also expire on this date. Alternatively the importer can arrange for a RAW to make an application during the transition period ie before the end of the 7th May to place a used import plate on the vehicle

any additional info required call Lal Goonewardene on (02) 6274 7500

so bottom line if you don't have a plate on your car by 7th May you are stuffed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...