Jump to content
SAU Community

Recommended Posts

Bad luck Mona. Will be interested to know if it's oil or fuel related.

Hows the oil in the sump look? Lots of golden flecks? May have just been a rod let go too. How does that look on the gudgeon (piston) end where it snapped off?Looks beaten on the lower part of the rod.

My advice for a daily driver though is RB25 with the right work and the right turbo. 26 is too lazy low in the revs and if you have a grabby clutch you will get some spin trying to get the thing going in the wet with RWD.

All the best on the new one and please post whatever you want in my thread below.

  • Replies 240
  • Created
  • Last Reply

Top Posters In This Topic

boost - 1bar

well confirm if the fuel pump is still working on not.. as far as i know she still is!!

Geoff - will do!! and yeah... losts of scrap metal and water droplets :w00t: Couldn't see the piston end.. only had a top view... so can't tell you what it looks like!

it's not that complex moonie..

look for the user CUBES. in his signature, he has a PDF file which is like a DIY rb30det guide.

go from there..

if you are going to be paying someone to fix your motor for you, might as well get them to do the 30 for ya.

probably cost less.

considering bottom end costs about $100

if you want forged goodies, then both bottom ends will cost the same.

small mod to the vvt oil line

small mod to the engine mounds and your done.

so to speak

Moanie who is having a look at the engine? like Geoff said it seems like the piston failed at the gudgeon pin which is pretty unusual? And we can't really tell if the rod broke as well.....and presumably when it all let go the piston mashed into the valves and head at eleventy billion miles per hour.

Normally pinging will blow out a ringland and you will loose a heap of compression before a rod or pin fails, so I'm wondering if there was some other cause?

moooooona

you had what, 250rwkw before?

on the same boost, on a STOCK (read: stock pistons, rods, crank, gasket etc) RB30 bottom end, you would have that power or more, with loads more torque earlier in the rev range, and would be more reliable.

If your head is ok, it would be the cheapest option for you.

if the head is gonesky as well, then you need to look at it a few more ways.

stock second hand rb25det from wreckers?

stock rb30 bottom end, with stock rb26 head with new rings and bearings?

I've seen rb26 heads complete with manifold, injectors and so on for about $2K

Justinfox is selling a pair of 2530's for $1K (one has s blown seal or something but thye were both built by GCG using HKS cartridge or something)

All bolted together you'd have some spastic amounts of power which a little girl like you could ever want.. :)

Not sure what sort of $$$'s you are looking at spending here or can afford to spend but think it all through and do the math before making a choice.

Finally... if you ever need someone to point and laugh at your misfortune, you know where to find me. well for the next 3 weeks anyway

:)

hahahahaa... yes indeed i do!!

thanks for the ideas! i'll look into those options.. it really does come down to what i need to fix! but we'll see!! and i have no money at the moment!! jsut what i wanted to spend on rims!!! so i'll be going a cheapish option as well!! we shall see! :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...