Jump to content
SAU Community

Recommended Posts

6x R33 GTST series 1 coilpacks with the dust cover and wiring loom for sale $150 SOLD

RB25DET Inlet manifold (needs minor repair) with throttlebody and with 6 injectors still in the rail with fuel reg (has metal gasket that joins the top and bottom half of manifold together $150 ono - SOLD

RB25DET exhaust manifold (stock) that has been modified to fit a RB30DET - used this on my 3 litre for 2 years no problems $75 SOLD

I am on the Central Coast. can meet you in Sydney - Central Coast - Newcastle.

Or postage

Thanks for the guys that purchased these bits from me. much appreciated.!!! all sold!!!!

post-1240-1146118624.jpg

post-1240-1146118928.jpg

post-1240-1146118954.jpg

Edited by Guilt-Toy

hey mate, what needs to be repaired on the manifold? if it IS only small and there isnt anything else wrong with it, ill take it. PM sent

also, does it come with all the sensors and hoses etc?

thanks

tom

Edited by kossak
hey mate, what needs to be repaired on the manifold? if it IS only small and there isnt anything else wrong with it, ill take it. PM sent

also, does it come with all the sensors and hoses etc?

thanks

tom

hey mate

the manifold comes with all sensors and hoses - check out the pic of the unit as you can see everything is there.

please get back to my PM

Thanks

COILPACKS STILL FOR SALE - $150 + delivery - these come with the wire loom the brackets the coil packs bolt into and the dust cover that sits over the top of them! great value!!!!

Has to go !!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...