Jump to content
SAU Community

Recommended Posts

Hey i just bought some new tyres and damn are they noisy. with my old ones which were wasted you did hear alittle bit of that ticking sound now its louder with these tyres. any maintenance tips to help the noise decrease or go away?? Correct me if im wrong but seems to be abit better when the tyres are warmed up abit.

Link to comment
https://www.sau.com.au/forums/topic/116583-noisy-tyres-hate-em/
Share on other sites

Hey i just bought some new tyres and damn are they noisy. with my old ones which were wasted you did hear alittle bit of that ticking sound now its louder with these tyres. any maintenance tips to help the noise decrease or go away?? Correct me if im wrong but seems to be abit better when the tyres are warmed up abit.

new tyres should be quiet, generally as tyres get older they will be noisier (wear, tread goes hard etc)

what tyres are they? did u get them brand new or second hand?

were they balanced when u put them on? i have found that i had a bit of noise at freeway speeds with my old tyres and so i got them rebalanced and it went away.

i just got new tyres today and my car feels like a limo compared to before :ban::D:P

What a load of horse @$#@! Why post if you have no idea what you're spouting! :blink:

The only time you should ever run less presure in the rear than the front is in a drag situation with the right tyres and suspension set up to handle it.

For tyres of that staggered size front to rear on the street, I'd recommend 36psi in the front and 38psi in the rears for even tyre wear, best handling and best fuel economy. 40 and above is too much and too rougher ride for the street plus at those pressures and your width of tyre it's highly likely that you'll get over inflation wear.

On to you problem at present. Your tyres, although being of the cheaper (nastier) variety, they should be quiet when new especially being new, balanced and wheel aligned! So i'd be heavily leaning towards rear wheel bearings!

With new tyres eliminating the old tyre growl you can now hear the wheel bearings. You typically hear them at highway speed as they're spinning at high speed making them more audible.

I'd jack the rear of your car up so your rear wheels are off the ground, sit the rear on jack stands and chock your front wheels and spin the rear wheels up to 100km/h and I'll bet you hear the growl still

Hope that helps :(

Edited by ellie

hahah nah I take too much care of my car to do stupid stuff in gravel carparks. i'll check rocks and stuff. after some further research they said these tyres are known to be loud so yeh great. As soon as they go bald im going for some toyo's :cheers:

hahah nah I take too much care of my car to do stupid stuff in gravel carparks. i'll check rocks and stuff. after some further research they said these tyres are known to be loud so yeh great. As soon as they go bald im going for some toyo's :D

I wonder how they'll go bald??? ;)

lots of sensible driving. Yeh the noise of the tyre is annoying. Im thinking of just changing them. Just a warning to you guys dont buy these brand tyres noisy az. I wonder why tyres do make the ticking sound its just crap hehe.

you can also hear it when like doin 60km/h also but once you drive for a while the tickin sound seems to go cause the tyres warm up. But for the time they are ticking embarrassing cause its like people think something wrong with ur car. should of stuck with the pirellis or did some research as people say they are loud as tyres. didnt think new tyres could be loud i guess its the compound or whatever.

I have never heard any tyre noises in my life..

Even on the shitty camry with new tyres and even old tyres which are bald ass..

I got pirellies (whateva spelling) on the camry and no noise!!

hmm as for pressure, always best of a 30-32 combo..

^^^^ Just about all tyres are noisy buggers. When you are fairly close to a major road, the first thing you notice is the tyre noise. After a few hundred metres you tend not to notice the engine / exhaust noise, but the tyre noise always carries a long distance.

As for ticking, I would be inclinded to think that there was a nail or screw in the tyre. Sometimes they are hard to see too, and you sometimes need to take the wheel off the car to easily tell where the nail / screw is.

Ticking might also be from brake pad wear indicators (strange but it could be). Dude tyre noise is NOT a ticking noise. Its quite posible these tryes are actually quieter, and you are now hearing another noise that was previously masked.

BTW, I run 38psi front, 36psi rear and have PERFECT tyre wear, took me 6months to work it out tho. I think it depends on the car and your driving style.

heheh also the pressure depends on the tyres you have!!

I had some shitty 205s on my car ages ago.. Anyways even with 30psi, i was spinnin in 1st,2nd and 3rd.. with a stock car!!

even set at 25psi, it was shit.. just kicked out easily..

Anyways back on topic.. next time i drive im gonna try n hear my tyres lol..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...