Jump to content
SAU Community

Recommended Posts

My car makes this clicking sound from the dashboard. It seems to come from behind the two aircon vents in the middle of the dashboard. Only sounds on when the car is started and/or the air con fan is on. If i start is without the fan on it doesn't make any sound but when I turn it on, it makes clicking noise 4-5 times and then stops.

Is this a relay of some sort behind the vent or somewhere else? Its been happening for the past two weeks on and off. Now its a bit more regular.

Any help would be appreciated.

I tried to open the dashboard panel (the complete piece which goes right hand vent and to the stereo/ac side) from the driver side by first removing the gear box panel. But the middle part is stuck because of the stearing column. I have seen an electrician pull the stearing column down by releasing the black lever underneath the steering column. How the hell do you release it? I can't see any sort of a locking mechanism on it. If somebody can tell me this then i can have a look myself and try to diagnose what is going wrong.

Thanks again.

HarryG

i think its your aircon gate thing inside the dash, it tries to shut itself every time you start your car but since it was not put back properly after the dash was striped, it keeps hitting the vent.

that is my understanding of the matter, have seen quite a few R33 doing this.

Edited by frankxy

Thanks frankxy, I think I know what the problem is now. When I have the ac on and i change the mode of the airflow from head and feet (two arrows) to feet only I get the clicking noise. That means when it's closing the top vents it's getting stuck somewhere. The vent does close because there is no air flow there but the sound is annoying. So i will get it checked out.

Would appreciate if somebody can comment about the steering column release lever.

I have the clicking problem as well when I have the aircon on, and when the car first starts up, and when the turbo timer kicks in. Mine has an aftermarket headunit as well, so when I change the headunit, I will look at the vents to work out what the problem is.

Mate i can tell u exactly what it is, well not the name of the part but yer, it's a part of ur aircon unit, they tend to go when it's old or not unsed on a regualr basis, they make the clicking noise when the air con unit changes speeds, it will only get worse. To fix the entire dash must be removed and the questionable part replaced, i had mine done at an auto electrical and air con place for around $600 bucks, most of this was labour pulling aout the dash, it's now back there with the same prob cause the car was left to sit for 9months in a shop for custom work and not started, will be alot cheaper cause the dash is out, just the cost of the part so u have a choice, big labour cost or pull the dash out yourself then take it to an auto elecy, dash in and out is a big paint in the arse, trust me, do it 3 or 4 times and u become an expert tho!

hey mate, u must pull out the entire dash, not just the surround be to replace the headunit, entire thing, the part is called a blend door actuator, once ur dash is out, if u plug the aircon back in and make it change speeds, (from 4 to 1) works best, u will see a little "arm" move as to the speed it's at, the actuator is attached to that, expensive and hard to get, i was quoted 250 out of japan plus tax and shipping but was lucky enough to get one from a wrecker for $88

I beleive there will be no harm. Mine's been doing it for 8 months or more. The actuator detects when the lever is at its end, so when it goes faulty, the mechanism doesn't stop trying to move the arm. Eventually it times out and stops anyway, so it should be ok.

i actually done this job last week my car had been doing it since i brought it.then my heater core died so fixed both probs at once. there is no easy way to do this and the whole dash must come out .with the actuator what happens is it strips the plastic gears inside and when it trys to open the vent door it wont move and just makes that clicken noise. we had never done one b4 so we was carefully when pulling the dash apart it took about 4 hrs we marked every plug to make sure things went back together as they should. and prob the same to put it back together but we had to fit the new heater box as well witch took a bit extra time .honestly if your not condident in doing it yourself then pay someone cause its not hard to break some of the plastic clips ect ect

its a big job and lots of patience is required

cheers good luck

Edited by iLEC

I have been advised that the piece making the noise is a common problem and is not even a necessary component to the functioning of the climate control system. Apparently Nissan stopped including it after some point anyway. So the advice i have received is they can remove it and bobs ya uncle.

By the way, this advice came from PowerPlay!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
    • They are in fact just nozzles. They are there only to produce a spray pattern and limit flow. The injector itself is what I use to control flow to the 7x nozzles. My old system had no injector and only PWM the pump. This lead to a lot of inconsistencies, and poor atomization at low pressure when the pump was ramping up. 
×
×
  • Create New...