Jump to content
SAU Community

Recommended Posts

its probably your coil packs. its a common problem in the r33's.

take them out and get the coil packs cleaned on the inside with some steel wool till theyre all nice and shiney on the inside.

its either that or your spark plug gap is too big (although 1.1mm should be fine on standard boost).

Link to comment
https://www.sau.com.au/forums/topic/117456-boost-issue/#findComment-2160411
Share on other sites

if theyre too far apart on higher boost the spark may get blown out by the force of the air entering the combustion chamber.

if the gap is smaller, the spark will have more of a chance of detonating the air/fuel at the right time as the spark has a smaller distance to travel.

a con of having a smaller gap is the spark wont be as powerful as a spark gapped at 1.1mm. this is why people buy splitfire coil packs and make their gap larger than the .8 that is recommended with standard coil packs.

hope that makes sence :D

Link to comment
https://www.sau.com.au/forums/topic/117456-boost-issue/#findComment-2161498
Share on other sites

yeah I concurr with everything that was just said! buy some XIs from Kudos motoesport in the trader section for 99 delivered...and also have a look at the coild backs for the hairline fracture...get some spitfires if u have the money...overwise do a dodge fix and u wil be set for a while...also while ur at it check ur leads...or just replace them...then u know everything is cool..

Link to comment
https://www.sau.com.au/forums/topic/117456-boost-issue/#findComment-2164389
Share on other sites

nah they dont need replacing, plus it isnt a dodgy fix if you're cleaning the inside of the coil packs with a dremil or steel wool.

over time they get a build up of crap inside them. this stops the route to the spark plug from being the shortest path to earth (which is how electricity behaves) as the build-up of crap is stopping the coils conduct with the spring properly under load. just clean out the shit inside it and you'll notice a huge difference. make sure you do it carefully though.

i did mine at around the beginning of last year and they were good till last december when i took my car off the road for blowing #6. and im sure they'll be fine for another few years. i even took the tape off when i did it and they worked just as well.. no missfire for a year.

heres what they look like before (not my coil packs):

IMG_4798Medium.jpg

and these are my coil packs after cleaning them:

DSC00577.jpg

Link to comment
https://www.sau.com.au/forums/topic/117456-boost-issue/#findComment-2164782
Share on other sites

its probably your coil packs. its a common problem in the r33's.

take them out and get the coil packs cleaned on the inside with some steel wool till theyre all nice and shiney on the inside.

its either that or your spark plug gap is too big (although 1.1mm should be fine on standard boost).

thank you for advice :)

Link to comment
https://www.sau.com.au/forums/topic/117456-boost-issue/#findComment-2175498
Share on other sites

Time for a bit more info on this thing :thumbsup: I didn't write a post up about it yet because the car needs to be repaired first (the accident or should I say incident was not her fault in the slightest, long story which I won't go into here). Anyway here's the basic rundown and why I don't think it's the coils.

Firstly, the old coils were good up until about 1 bar of boost, then it would get the misfiring problem at anything higher which I discovered when I had it tuned last year. So I got Splitfire coils which fixed it. Before selling the car I decided to put it back to stock(ish), but tested the old coils at 1 bar first, to make sure that they were still ok. Everything was fine.

So then I put the rest of the stuff I was selling back to stock. Injectors, ECU, AFM. Then I noticed that it was getting the misfire problem again, at about 5000rpm as seems to be the norm. Luckily I still had the Splitfires so I threw them back in to see if that helped, and it didn't make even a slight difference. So I was and still am 99% sure that it's not the coils.

Next thing to test was the AFM. I couldn't put the Q45 AFM and PowerFC back in because they had been sent to their new owners already, but luckily Andrew from Kudos Motorsports sent me a stock replacement express post (thanks Andrew!), and this seemed to make a difference. Instead of misfiring ALL the time, it was now doing it maybe half the time and seemed to be improving. I then decided it was the factory AFM making it run too rich and fouling the plugs, but now with the new AFM it was running correctly and blasting off the carbon.

At this point I decide to put the car on the market, but Emma gets a new job and says she can afford to buy it, so she is driving it around herself for a couple of weeks before she has the incident mentioned above. During that time though we discovered that the misfiring problem was gradually returning. I found that I could lessen the effect by winding the boost down, but gradually it started happening at lower and lower boost. Even though the EBC was set to 0.6, I think that the adjustable wastegate actuator is set to around 0.8 so I don't think we've managed to drop it any lower than that. I would need to road test it to check but obviously that's not possible yet.

Other things I've tried were changing the plugs to new ones, it didn't make any difference and the old ones weren't fouled anyway so now I have a spare set. My current theory is that it's factory boost cut, but I unfortunately don't have a PowerFC anymore to test this theory. The turbo is not stock, it's a 450hp Garrett so this would generate extra problems for the factory ECU. The fact that the misfiring issue is moving around depending mostly on the changing of air flow (boost) or measuring it (AFM) makes me think that the ECU is "learning" how to cut the boost again whenever I change something, similar to how it learns how to idle, and back off timing when it detects detonation. A simple test will be to reset the ECU once it's on the road and see if it improves anything.

I think that's the whole story! I was going to post all this up after the car was back on the road, but Emma's very eager to learn and she thought she'd put the post up about it :P

Link to comment
https://www.sau.com.au/forums/topic/117456-boost-issue/#findComment-2175810
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
    • The hydrocarbon component of E10 can be shittier, and is in fact, shittier, than that used in normal 91RON fuel. That's because the octane boost provided by the ethanol allows them to use stuff that doesn't make the grade without the help. The 1c/L saving typically available on E10 is going to be massively overridden by the increased consumption caused by the ethanol and the crappier HC (ie the HCs will be less dense, meaning that there will definitely be less energy per unit volume than for more dense HCs). That is one of the reasons why P98 will return better fuel consumption than 91 does, even with the ignition timing completely fixed. There is more energy per unit volume because the HCs used in 98 are higher density than in the lawnmower fuel.
    • No, I'd suggest that that is the checklist for pneumatic/hydraulic adjustable systems. I would say, based on my years of reading and complying with Australian Standards and similar regulations, that the narrow interpretation of Clause 3.2 b would be the preferred/expected/intended one, by the author, and those using the standard. Wishful thinking need not apply.
    • Yes they do. For some maybe. But for those used the most by abusers, ie Skylines, the numbers are known. The stock eyebrow height for R32/3 Skylines is about 365/375mm or thereabouts. The minimum such heights are recorded in adjacent columns in the database.
×
×
  • Create New...