Jump to content
SAU Community

Recommended Posts

Anyone broken their remote rear seat handle in the boot ? seems pretty fragile for the force required to pull the cable and release the seat. Also, realised today that the rear seat can be laid back for extra comfort, using the handle next to the seat. thought that the rear seats were a little too upright.

Link to comment
https://www.sau.com.au/forums/topic/117693-remote-rear-seat-lever/
Share on other sites

Mines not broke, but then I dont get to use them often with 3 baby seats and all. If you have to pull harder then one finger then you got a seized cable or locking mechanism problem.

Yes, reclining rear seats are just another sweet Stagea touch, designed by someone who actually thought about what might be useful.

Now that you've broken it - what's it made of - plastic or metal?

Edited by 3intheBack

Mine dont need much force at all to get them to work.... Also my kids found the recliner lever and now proceede to change it constantly to match their mood I guess.

I guess they copy me as first thing I do when I get in is seatbelt, then make tiny adjustments to mirrors and seat and then start her up.

I broke one of mine ;) cost $68 for a new one from Nissan.

That's not too bad seeing this on yahoo japan.

Around $50AUD purchase price only.

I have a feeling you may have paid $68 for the plastic handle only though...

Edited by munchdesign
That's not too bad seeing this on yahoo japan.

Around $50AUD purchase price only.

I have a feeling you may have paid $68 for the plastic handle only though...

Nope, it came complete, handle, bracket and cable :(

  • 2 months later...

Well my passengers side lever went this morning, went to drop the rear seat, didnt yank on it or anything, and snap.......

So what is the part number, for the passengers side one, I'm guessing the drivers side and passengers side will have different part numbers?

hey cyrus dont u reckon a dedicated sticky thread with stagea part numbers for parts us members buy would make it very easy and handy for others when it comes to ordering bits and pieces. im talking all parts like manual console surrounds, to these handles, and cargo covers, and anything inside or outside the stagea :miner: virtually a nissan fast part no. thread to save the nissan dealers from trying to find part no's on the Fast programs.

good or bad idea? :rofl:

cheers

Brad

hey cyrus dont u reckon a dedicated sticky thread with stagea part numbers for parts us members buy would make it very easy and handy for others when it comes to ordering bits and pieces. im talking all parts like manual console surrounds, to these handles, and cargo covers, and anything inside or outside the stagea :miner: virtually a nissan fast part no. thread to save the nissan dealers from trying to find part no's on the Fast programs.

good or bad idea? :rofl:

cheers

Brad

i think its a great idea save the screwing around and stuff

hey cyrus dont u reckon a dedicated sticky thread with stagea part numbers for parts us members buy would make it very easy and handy for others when it comes to ordering bits and pieces. im talking all parts like manual console surrounds, to these handles, and cargo covers, and anything inside or outside the stagea :P virtually a nissan fast part no. thread to save the nissan dealers from trying to find part no's on the Fast programs.

good or bad idea? :D

cheers

Brad

Already done, there is a parts list, the link is in the sticky mega link thread :)

Here ya go Ska, have replaced the same one in mine, cost bout $69, bit of work involved too, have to remove the complete rear left interior trim to get to it.

88925-0V015

Yes well I had to have a fiddle didnt I :angry:

Well after 4hours of unscrewing and removing bits and pieces I found out why my ATESA isnt working right, one of the wires had worn through and was shorting out on the body, so whacked a bit of electrical tape around it and zippy tied it away from where it had worn through.

Anyway, I followed the line through and near the release mechanisim on the seat itself there is a white bit of plastic which sits around the cable and then slots into the unlocking mechanisim, one side of it had broken off, the plastic was a bit detiriorated, so I whacked a bit of superglue on it and let it dry, hey presto, works like a charm :P

Then it only took about 2hours to get it all back in, :D What an adventure :)

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...