Jump to content
SAU Community

Gt Wings

HIPSI

By HIPSI,
in Western Australia

 Share

Recommended Posts

JUNR34 Community Regular

JUNR34

Posted
Posted

Im sure some cops will still pick on the fact that the brackets are metal, but should be alright if the actual wing isnt metal. Its illegal if its wider then the car also if the sides of the wing are sharp. Its a bitch getting a yellow sticker having to wait for your turn at the pits plus 50 bloody dollars, too troublesome.

Link to comment
https://www.sau.com.au/forums/topic/118328-gt-wings/#findComment-2177525
Share on other sites
HIPSI Experienced

HIPSI

Posted
  • Author
Posted
Im sure some cops will still pick on the fact that the brackets are metal, but should be alright if the actual wing isnt metal. Its illegal if its wider then the car also if the sides of the wing are sharp. Its a bitch getting a yellow sticker having to wait for your turn at the pits plus 50 bloody dollars, too troublesome.

Yeah that's what I rekon, I can't be bothered with the hassle from the po. I might just take it off, looks pretty sleak without it anyway

Link to comment
https://www.sau.com.au/forums/topic/118328-gt-wings/#findComment-2177967
Share on other sites
gazza750 Veteran

gazza750

Posted
Posted
Well so far no reply on my email I sent, doubt I will get one too.

usually takes em about a week for welshpool to reply to emails about car mods took 8 days for me to find out about legallity of pod filters through email from them

Link to comment
https://www.sau.com.au/forums/topic/118328-gt-wings/#findComment-2181922
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...