Jump to content
SAU Community

Recommended Posts

:yes:

I was hosed as :laugh:

My bad if I embarrased you!!

BAHAHAHA

*dance*

*holds tummy*

Im still a lil fragile

:)

She wasnt embarassed, we just had to go and see heaps of people :w00t: Next time we will stay longer

We were going to come back but then the lure of the boob pulled us in lol

She wasnt embarassed, we just had to go and see heaps of people :) Next time we will stay longer

We were going to come back but then the lure of the boob pulled us in lol

yeah they're good at doing that...

i wish i saw tits.. oh wait i did!!

bahahaha

:laugh:

not stripper boobs though :w00t:

it's cool... i'll hafta have a good vodka drinkin sesh with the lil anna!!!

:yes:

double blacks=anna wants to vom!!!

:)

Is that a challenge?

Cos no one's even seen Nikita and I at our full potential

MUHAHAHAHAHAHAHA!!!

:laugh:

i believe its a challenge, jsut tell us where and when and ill bring the video reorder :w00t::yes:

yeah they're good at doing that...

i wish i saw tits.. oh wait i did!!

bahahaha

:yes:

not stripper boobs though :D

it's cool... i'll hafta have a good vodka drinkin sesh with the lil anna!!!

:)

double blacks=anna wants to vom!!!

Next time we will invite you along! I was a little ermmmm forgetful on Saturday :w00t:

boobs aye, were did u go and view these boobs?

Showies of course...twas a good noight too! All the old scholl girls were there! The quality was back :laugh:

morning there mike :laugh:

whats the car sound like? a rotary? :yes:

more like a 13btt actually, very quiet. until you get up it, then it sounds like a 12a

Whaddya mean it has no wastegate??

i couldnt see any wastegate or BOV, just a turbo.

wasnt running the intercooler aye, just like how them vl's ran no intercoolers :laugh:

lol no this one just wasnt hooked up. it was running through it, but it wasnt connected yet (water-to-air cooler)

more like a 13btt actually, very quiet. until you get up it, then it sounds like a 12a

i couldnt see any wastegate or BOV, just a turbo.

sooo its an internal wastegated turbo then :laugh:

more like a 13btt actually, very quiet. until you get up it, then it sounds like a 12a

i couldnt see any wastegate or BOV, just a turbo.

IT has to have a wastegate or it would run unlimited boost, it must be internally gated

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...