Jump to content
SAU Community

Recommended Posts

Be very very careful of treads international they sold me defective tyres and wouldn't give me my $$$$ back

Lee you have the shitess luck whe it comes to your car :O

man i feel lucky i own a sil with a good condition engin....

hey andy..

my brother was actually. he took it..

story time..

my brother decided that he is capable of doin a service on the R34. so he goes on about it. and nips the filter rubber seal and splits it as he fits the new filter.. he starts it up and leaks 4 litres of $70 of castrol edge 10w-60 oil on the ground.. then he goes off buys new oil from repco.. and puts her back together.. he does a very rough job cleaning up. he destroys 2 bath towels, my car washing sponge and 2 rolls of toilet paper and a newspaper trying to clean then he goes off to garden city without emptying his old oil into the oil container or cleaning the driveway properly. he just left everything and went. didnt clean up.. hes so incompetent..

hey andy..

my brother was actually. he took it..

story time..

my brother decided that he is capable of doin a service on the R34. so he goes on about it. and nips the filter rubber seal and splits it as he fits the new filter.. he starts it up and leaks 4 litres of $70 of castrol edge 10w-60 oil on the ground.. then he goes off buys new oil from repco.. and puts her back together.. he does a very rough job cleaning up. he destroys 2 bath towels, my car washing sponge and 2 rolls of toilet paper and a newspaper trying to clean then he goes off to garden city without emptying his old oil into the oil container or cleaning the driveway properly. he just left everything and went. didnt clean up.. hes so incompetent..

I parked opposite it in the car park. The wheels looked good...a different colour my be better but

I want to go home!! Man its Friday... i so dont want to be at work...

so which one of your ladies are coming to the mountain run??

its more of a crusie than a run..

Hmm anyone know how to remove teh speed limiter of the car?

diffrent engin management.... piggy back computer...

i'm pretty sure a fuel cut deffender will do it too..

why bryn back to your old antics again??? man sell the skyline and buy a dam commonwhore your making us all look bad :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...