Jump to content
SAU Community

Recommended Posts

Thanks <3

I can have my interview anytime Im ready at Sherrin motorsport, was just holding out to borrow the R33 to tie me over for a few weeks. Interview = job = move straight away :)

I can get the RWC up here for those wheels, but as I told Anna I will need the car

borrow the R32 for the day i dont care!

borrow the R32 for the day i dont care!

The problem is, I can get the interview but they are talking week or so trial! lol I don't really have cash money I can pull out to buy a car in the event to dont end up getting the job

The problem is, I can get the interview but they are talking week or so trial! lol I don't really have cash money I can pull out to buy a car in the event to dont end up getting the job

i see

where is the place you have to get to?

Hamilton, car isn't need for the job AFAIK, just getting there and back to your house is the situation.

if you were keen to start public transport to there would be easy

there is a train that comes to our station and goes on the doomben line, hop off at Doomben and you are pretty close! Maybe walking distance maybe a bus or somthing

if you were keen to start public transport to there would be easy

there is a train that comes to our station and goes on the doomben line, hop off at Doomben and you are pretty close! Maybe walking distance maybe a bus or somthing

HAHAH, i knew you were going to say that. It's ina c*nt hole of a spot, no transport to where the work shop is, although yes train to Hamilton it's self is doable. I so ca have that ego next week Andy :) Just think back on the road and ready to sell for the Evo!

Note to self:

When attempting to remove one's airbox from one's car, be sure to know the location of one's socket set BEFORE starting. A pair of different sized shifters, a screwdriver as a lever and a set of needle nose plyers does not a socket set make.

HAHAH, i knew you were going to say that. It's ina c*nt hole of a spot, no transport to where the work shop is, although yes train to Hamilton it's self is doable. I so ca have that ego next week Andy :) Just think back on the road and ready to sell for the Evo!

ok I will borrow Daves stock wheels and get it regoed can you and Anna organise that one day through the week? I dont even know what you have to do!

ok I will borrow Daves stock wheels and get it regoed can you and Anna organise that one day through the week? I dont even know what you have to do!

I can get a RWC with the 18's! I'll be down Wens, when I saw Anna on Tues I said if she wanted we can do rear tires and I'll pop down at night to take it back up to my place to get it RWC the following day then come back down for u guys to rego it.

dont worry about the no rego thing... it doesnt faze me

HAHAH, i knew you were going to say that. It's ina c*nt hole of a spot, no transport to where the work shop is, although yes train to Hamilton it's self is doable. I so ca have that ego next week Andy :) Just think back on the road and ready to sell for the Evo!

More of a walk than from that train station near slips house to ADD?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...