Jump to content
SAU Community

4 X Gt4088r Garretts

danielson

By danielson,
in For Sale (Other Items)

 Share

Recommended Posts

danielson Proficient

danielson

Posted
  • Author
Posted

for sale are four genuine BRAND NEW GARRETT gt4088r dual ball bearing water cooled turbochargers. These retail for aroung 2800bux, and i am selling these for $1000.....

GENUINE GARRETT NOT CHEAP CHINA JUNK!!!!!! BRAND NEW BARRETT GT4088R, RATED AT 700HP , specs as below

http://www.turbobygarrett.com/turbobygarre...T40/GT4088R.htm

BE QUICK AS THESE ARE LISTED ELSEWHERE, A THOUSAND BUX FOR A LEGIT 3GRAND TURBO!!!

PM ME FOR DETAILS

danielson Proficient

danielson

Posted
  • Author
Posted (edited)

If you read above it says PM ME FOR DETAILS. this is why i havnt checked back on this thread. these are 100% legal, i would never put myself in such a situation. they are direct from the manufacturer..... And no, these will not be a direct fit onto a rb25det manifold, as they are a t4 exhaust flange, rb25 uses a t3 flange.

Edited by PranK

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • PranK
      Most women will agree that parking is the most taxing part of driving

      By PranK · Posted

      Go back and watch the video again... 
    • funkymonkey
      Most women will agree that parking is the most taxing part of driving

      By funkymonkey · Posted

      Are you meant to double fist them?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
×
×
  • Create New...