Jump to content
SAU Community

Recommended Posts

I picked up my R32 GTS-T last night, Only problem was the lights behind the dash were out :O

The guy I bought it off offered to fix but I wanted to drive it asap so I said I'd do it.

I'm sure its an easy job but I don't have the service manual yet (anyone know a source?)

The clock backlight works fine its just the gauges that are affected. If one of the backlight bulbs blows, I assume the others keep working? If so it means its just a fuse issue since all the gauges are out?

I checked the interior fuses and didn't find anything blown (though some were missing, probably the spares). I ran out of daylight to get to the engine bay fusebox. Does anyone know where the fuse is?

I really need to get that service manual :O

Cheers guys

Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/
Share on other sites

Could be a stupid question on my part, but do you have a dimmer knob? Most Skylines have one installed by compliancers as part of the import compliance rules. Mine looks like a vintage amplifer knob. =-o

I fiddled with all the knobs ... erm wait... played with.... errmm...

the knob isn't turned down anyway :(

Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2205923
Share on other sites

the wires too the dimmer could have fallen off.. mine was very badly installed..

worth a check if you cant see any fuses out...

edit : does the air con unit and head deck dim when you turn on the lights .. if not that means it isn't getting power.. which would support the fuse/wiring issue rather than blown globes

Edited by Craved
Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2205944
Share on other sites

Ah! Good diagnostic there, Craved!

Definately try that one, it should confirm power for you, or as Craved said, check out the install of the dimmer. Getting that whole dash panel loose can be done by following the stereo install guides for R32's.

Check those fuses first, cause it's easier to do than loosen the panel.

(oh, and don't fiddle with your knob too much, otherwise it'll go stiff and you'll need to lube it up)

Edited by RANDY
Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2206158
Share on other sites

:sweat: @ Steve playing with his knob :) You know, you must be careful when you select knob placement. Never expose it unnecessarily - discretion is the order of the day.

Dude if it turns out you need to replace your dash bulbs, try http://www.skylinesaustralia.com/forums/in...howtopic=115618

Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2206431
Share on other sites

I checked tonight and the climate control dims when I turn on the headlights :cheers:

Looks like I'm taking apart my dash. I may aswell redo the entire thing in LED's so I won't have the problem again for a long time, just have to decide which color to go for now

Cheers for all your help

Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2208430
Share on other sites

Matt yell out if you need a hand. It's actually a lot easier than you think. I've just changed my climate control to blue (to match headunit). It's not as groovy as I thought - doing it again I'd probably opt for 1000mcd white LEDs to keep it all low-key. If you choose 3000mcd LEDs you will be more affected by the 'directionality' of the LEDs. That is, it will be harder to diffuse the light and make it appear more like a glow and less like a laser pointer.

Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2210594
Share on other sites

Hey dude if it was a globe only one would be out but because there isnt any light on the dash at all indicates the fuse is blown. It will be the fuse box in boot next to battery. Its the one that says tail light L i think it said. 3rd fuse from the bottom on the left side. Should be a 10amp fuse. Thats for a R33 but i guess the fuse in your engine bay would be same as mine in the boot so check it out before pulling apart ure dash.

Adam.

Edited by Woodys
Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2220926
Share on other sites

cowie165 -- Can you provide me some steps in how you did this. My climate control lights dont show up, so i would be happy to fix it and replace it with leds. Which exact ones did you b uy and from where? Also steps involved please!!

Ahh you got a 32.. Shouldnt be much different tho?? Or type of leds are different??

But please let me know.

Sidd.

Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2222118
Share on other sites

cowie165 -- Can you provide me some steps in how you did this. My climate control lights dont show up, so i would be happy to fix it and replace it with leds. Which exact ones did you b uy and from where? Also steps involved please!!

Ahh you got a 32.. Shouldnt be much different tho?? Or type of leds are different??

But please let me know.

Sidd.

have a look here Sidd

http://www.skylinesaustralia.com/forums/in...opic=112729&hl=

Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2223648
Share on other sites

cowie165 -- Can you provide me some steps in how you did this. My climate control lights dont show up, so i would be happy to fix it and replace it with leds. Which exact ones did you b uy and from where? Also steps involved please!!

Ahh you got a 32.. Shouldnt be much different tho?? Or type of leds are different??

But please let me know.

Sidd.

Hi Sidd.

The 'grain of wheat' bulbs are the same in R32 and R33. The link Craved posted would be great for replacing with 12V bulbs. I tried Jaycar unsuccessfully - didn't realise DSE had what I was after in 12V with wires only.

If you are interested in the LED route, this post and onwards has bits and pieces on how to do it. Very simple and effective. If your dash dimmer also dims the climate control, I recommend 3000mcd LEDs, otherwise 1000mcd with the 500mW resistor. As the bulbs are the same between Skyline models the LEDs will be substitutes also.

The steps and a few reference pics are in the thread/post below. I hope it helps :thumbsup:

Mark

http://www.skylinesaustralia.com/forums/in...dpost&p=2145079

Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2225836
Share on other sites

Ok im having the same problem with my dash i just recently bought the car, and it keeps blowing fuses for my deck and just today my dash lights dont work i also have pillar mounted tacho's and a monster tacho and they dont turn on either but when i put my car in reverse everything turns on normally? i had undercar neons (that were done pretty bodgy by the looks of the wiring and the on/off button) but i smashed my drivers door and the neon got ripped off and the wire is still haning under the car i have tried everything i can but i need help anyone with any information can you please let me know thanks

GTR-TZR

Link to comment
https://www.sau.com.au/forums/topic/119681-dash-light-help/#findComment-2227358
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...