Jump to content
SAU Community

Recommended Posts

GDay,

I need to sell the following items:

1 x R33 GTR oil pump. Used for about 5000kms. Replaced due to upgrade. No damage. $100

1 x Hybrid Bar and Plate intercooler. 600 x 300 x 76mm. Excellent condition. $100. (Intercooler now sold)

Postage extra.

Ive also got an air conditioning compressor off an R32 gtst. $100.

1 x Alternator (R32 gtst) $100

1 x R32 gtst HICAS power steering pump. $100

All the standard air conditioning equipment off an R32 gtst. Condenser, thermo, all lines intact. $100 the lot.

Standard R32gtst air box. $50

Standard R33 GTR exhaust manifolds $70 neg??

1 x rooted R33 GTR turbo $50 neg

1 x R33 gtr starter motor, excellent condition. $150 neg

Shaun

0414972596

post-11456-1148965453.jpg

post-11456-1148965476.jpg

Edited by Shaun

Yes im sure it will. Im not sure if you need a crank collar to prevent premature failure of the oil pump drive gear that is common in R32 gtrs though.

Id ask someone in the know before purchasing though. The pump has seen very little use.

Shaun.

Ill have to do it in a few days time, as im working til tuesday and the cooler is at my parents place. It has three anchor points (one middle top, and two at the bottom) which take 8mm bolts, Its a standard gtr size, bar and plate construction, ive polished it on an 8inch bench polisher, no damage. In the photo, it looks like there are heaps of bent fins for some reason, however this is not the case. It performs really well, as i had inlet and outlet temp sensors on my IC piping. The inlet temps were never much above ambient with a GT30 at 19psi.

Shaun

0414972596

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...