Jump to content
SAU Community

Gtr Cluster On Gts

Konrad

By Konrad,
in Exterior & Interior Styling

 Share

Recommended Posts

Konrad Grand Master

Konrad

Posted
Posted

Hi guys & gals just a quick question,

Will a r33 gtr cluster plug straight into a 33 gts?? The plugs look very similar. (see attached pic of rear of a 33gtr cluster)

I searched but could not find any specific information about this.

Thanks in advance :P

-Isaac.

post-20414-1149397716.jpg

Link to comment
https://www.sau.com.au/forums/topic/120830-gtr-cluster-on-gts/
Share on other sites
MR R33 Experienced

MR R33

Posted
Posted

Yes it should fit, but as i found out, if the speedo is above 180km/h eg. i have a nismo 300km/h speedo, you will have to get it recalibrated, other then that it fits. Also if its a gtr speedo, you will not have a boost guage on the rev tacho.

dave...

12DFY Collaborator

12DFY

Posted
Posted
Thanks for the info dave :P

So you have one fitted to your car and it just plugs right in?? boost gauge isn't a problem since i dont look at it anyway (have a proper one on my a pillar).

I have done it on R33 sedan, fits straight in. Need to calibrate speedo as diff ratio on GTR is different

12DFY Collaborator

12DFY

Posted
Posted
how do you recalibrate the spedo?? is it done on the car or do you need to take it to someone and supply them with the diff ratio of my car??

To get it calibrated you need to get it onto a dyno and get the readings for 60 80 100 km/h on the dyno. Note the dyno speed compared to gauge speed. Take instrument cluster to a boffin/instrument type electronics person and they will know what to do. I skipped this step as I just put the same ratio diff as a GTR in me car.

  • 3 years later...
Jaysiin Enthusiast

Jaysiin

Posted
Posted

digging up an old thread.....

i have 2 spare dashes laying around.....

i was assuming if it was a 320km/h etc speedo it will require recalibrating of such.

will the 180km/w gtr cluster plug and plug on a gtst or will i have to re calibrate it as well due to the diff ratio?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Is it alright to top up with just another green coolant?
    • Songo
      New kid on the block

      By Songo · Posted

      thanks GTSboy. My confusion at the moment is i am trying to locate the ignition, ECU battery power and the ECU negative The closest thing i can find is the for the S15 on Page 8 of the Wiring Specialties web page https://drive.google.com/file/d/0B9F33_M_GgENQnZ6STMxVmVNd1E/view?resourcekey=0-eZ4nNRwRoqa1qvKlWWHm8A I cannot find the same diagram for the R33 RB25DET Series 2 dash plug pin out.... Do you know what the Pins? or know where i can find the same pinout diagram for the RB dash plug? Thanks for the advice on the box... i like a 6 speed so might be on the lookout or the box now.. a topic of discussion for another post...
    • Chupapy
      Coolant leak?

      By Chupapy · Posted

      Will have a look at that. I cant see any leaks 
    • GTSBoy
      Coolant leak?

      By GTSBoy · Posted

      Put another overflow bottle (ie, a 1.25 coke bottle or similar) under the overflow hose and see if it is being pushed out there or if it is disappearing into the engine.
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      Staring on a stand is no issue. You just have to wire everything up, give it fuel and cross your fingers that the stand is robust enough. Arranging the inlet plumbing is often the hardest part, without any surrounding structure to hand some of it from. No need for coolant if you only want to run it for <1 minute. As to the gearbox - I think the little Aisin box is a bit stronger than the other small Nissan boxes that went behind SRs, but I wouldn't be too keen to test its limits with the torque of a boosted 25. I don't know if you can retain the box and the tailshaft. The box won't connect to the RB without an adapter of some sort, which is either a plate that will push the engine forward (which is not good for fitting it into the bay's available space) or push the box back, which messes with the box position and tailshaft length - OR - cut and shut work on the bellhousing, which is a long way from "least modification". I'd be buying a new 370Z 6 speed or similar, doing what has to be done to that to make it fit RB (ie, cut and shut bellhousing) and the requisite tailshaft custom/mods.
×
×
  • Create New...