Jump to content
SAU Community

Recommended Posts

oh hell yeah... i loved my justjap cooler.. will prbably get another for my r32... great quailty... pressure drop was non existant at 10psi and cooling efficiency was fantastic

i think unless your persueing massive horsepower.. hks and other brandy are just a waste of money

-Ruffels

Link to comment
https://www.sau.com.au/forums/topic/121381-just-jap/page/2/#findComment-2248487
Share on other sites

so by gathering most peoples commnets, say 250rwkw would be sufficient for just jap coolers?

Easily, they have customers running their bar and plate intercoolers on heavily modified vehicles running between 300-400rwkw happily

250-300rwkw is no problem at all.

Link to comment
https://www.sau.com.au/forums/topic/121381-just-jap/page/2/#findComment-2248819
Share on other sites

Yup a friend of mine bought a delta fin core when it first came out. THink it was last year!! Worked great on his modded 33.

Justjap sell the delta fin core for 199. Not to sure on cost of piping or the whole kit deal.

But very nice looking core indeed.

Link to comment
https://www.sau.com.au/forums/topic/121381-just-jap/page/2/#findComment-2248889
Share on other sites

I had one of those delta fin cores which I bought when they first stepped into australia. Had it on the car for over a year, and had no dramas what so ever, was pushing 211rwkw.

Looks nicer than the typical bar and plate cores, and efinately lighter...

If anyone wants to buy my tube & fin genuine hybrid core, its up for grabs as im keen on another delta fin one :)

Link to comment
https://www.sau.com.au/forums/topic/121381-just-jap/page/2/#findComment-2249328
Share on other sites

Easily, they have customers running their bar and plate intercoolers on heavily modified vehicles running between 300-400rwkw happily

250-300rwkw is no problem at all.

Yep, i have one on my R33 GTR 326rwkw no problem I have an inlet temp gauge plumbed after the intercooler and my inlet temp even on the dyno with 25psi is 40degrees max, on the street it is normal to read just over the days temp.

Awsome for the price :)

Link to comment
https://www.sau.com.au/forums/topic/121381-just-jap/page/2/#findComment-2249879
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...