Jump to content
SAU Community

Gt30r Internal Gate Fit In Stock Turbo Location For R33 Rb25det

alpinestars
 Share

Recommended Posts

alpinestars Experienced

alpinestars

Posted
Posted

hey guys

was wondering if the GT30R internal gated will fit in the stock low mount position of the factory turbo

if so is it an easy fit or a tight fit and are the water and oil lines easy to setup for this

cheers guys

andrew

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

well there are no int gated housings at this stage in that line... still not out from garrett...

So what housing have you had machined up?

What A/R is it?

Is it a R33 rear housing? VG30?

alpinestars Experienced

alpinestars

Posted
  • Author
Posted

garrett has a line of them in internal gate, its on horsepowerinabox site and racespec site

A/R they have are 0.63, 0.82 and 1.06 i want the 0.63 for quicker spool

and im not to sure what housing it is but mounts onto my t3 manifold

The Dan Grand Master

The Dan

Posted
Posted

That is a custom made jobby from hpiab. They are a VG30 second hand rear housing from memory.

Garrett is just about to release the intrnal gated GT30R this month. I should find out this week.

In answer to your question though...the turbo will need to be spaced away as the comp housing is rather large. The oil and water lines will need to be made up. I suggest braided. These can be made for around the $250 mark. The inlet will also have to be changed due to the large turbo mouth.The dump pipe angle will also change so you might have to cut it under the car and rotate then re-attach.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

As 3lit said, they are not on the market yet.

So you've got the VG rear... alhough im now worried about what comp wheel it has in in...

But on the matter at hand, as 3lit also said, youll have to change all the stuff around it

sinistaGTR Grand Master

sinistaGTR

Posted
Posted (edited)

havent they been out at gcg and unique autosports for ages..... we are talking bout the gt3040 arent we???? if so someone else on here has done it in the stock position i remember lookin at it has the whole install process on photos, i think its in the forced section

Edited by sinistagtst
alpinestars Experienced

alpinestars

Posted
  • Author
Posted

i havent got it yet aye im just hell interested in buying one when they come out or if they are available atm

for around the 2k mark there the only turbo from garrett that are rated for more than 400hp

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

well they are a hybrid, not an "offering" from Garrett at all

What about...

http://www.gcg.com.au/Catalogue_Menus/Upgr...pgrade_gtst.htm

Another hybrid, well tested, well proven

alpinestars Experienced

alpinestars

Posted
  • Author
Posted

well im tossing up between that gcg highflow or a gt30r but gt30r more work to be applied to make it all fit in and running where as the gcg is all staight in straight out

my aim for the car is to get 350 rwhp

Sydneykid Grand Master

Sydneykid

Posted
Posted

GCG Ball Bearing High Flow on the Group Buy for $1750 delivered with all the parts necessary to fit straight on.

http://www.skylinesaustralia.com/forums/in...howtopic=121128

:P cheers :)

R33PWR Contributor

R33PWR

Posted
Posted

If you want 350rwhp an you get the gcg high flow factor in doing your cams as well, I have searched on these forums and not that many high flows have reached your figure of 260 rwkw.

The GT30R will be able to achieve this figure easily with more tuning maybe more, I have had a good look into the two myself. Im going with the GT30 I guess it depends on a few other things though as well like wat are you wating to do with 350rwhp ,track ,drift ,1/4. Wat other supporting mods would be in place to back up the turbo.

alpinestars Experienced

alpinestars

Posted
  • Author
Posted

well the car is set for track

i have pfc, fmic, pod, z32, ebc, fuel pump and fuel reg, turbo back zorst and when i get the turbo ill get bigger injectors

my car is tuned at 261 hp on a base/safe tune due to my turbo seal goin it cant be tuned for more otherwise bang

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

*sigh* they are external only.

any internal models are having other housings machined up to suit as the garrett items are not yet released

if people cant understand that yet i give up

BezerkR32 Veteran

BezerkR32

Posted
Posted

have seen a similar turbo low mounted, it was off the new falcon, featured ar.7 compressor cover and ar.82 rear internally gated. extensive modification of the engine mount necessary. plus custom plumbing in speedflow for oil & water feeds and custom dump pipe, intake pipe & intercooler pipe. looks fully standard though, cant pick it other than the large intake pipe.

hey guys

was wondering if the GT30R internal gated will fit in the stock low mount position of the factory turbo

if so is it an easy fit or a tight fit and are the water and oil lines easy to setup for this

cheers guys

andrew

alpinestars Experienced

alpinestars

Posted
  • Author
Posted

well im swaying more to the gcg as there is minimal work and expense to install is and running it

and if this turbo can give me 330-350 rwhp ill be happy :D

cheers

andrew

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...