Jump to content
SAU Community

Greddy Spec-m Intercooler Kits! Under $800. Wow!~!

JDMimports
 Share

Recommended Posts

JDMimports Mentor

JDMimports

Posted
Posted

GREDDY SPEC-M COOLER KITS $795 Greddy $795

The latest product release from Greddy Japan.

We've had a huge response and with our bulk order we've been given the opportunity to offer selected kits for just under $800.

Greddy intercoolers offer the perfect balance of heat exchanging efficiency and flow. The ends of the cores are TIG-welded and capped off with smooth flowing heavy-duty cast aluminum Greddy polished endtanks. Light-weight mandrel bent polished aluminum piping, complete with 2 ply hose couplers, are used to route air charge smoothly to and from the intercooler.

The Spec-M consists of a proven 280x600x76mm 2 layer core completed with the trademark Greddy polished end tanks. Superior polished piping engineered to fit right the first time.

Kits are available for RPS13, PS13, S14, S15, ECR33, HCR32

Local replacement warranty will be available for these sets unlike some of the cheap cooler kits found online.

With our first batch only weeks away, be the first to snap up the only Japan produced intercooler kit for under $800! Minimum deposit required to secure incoming stock.

Limited stocks arriving!

Only $795

0008.jpg

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...