Jump to content
SAU Community

Recommended Posts

You all know I am not up with all the technical terminology, so I will state it simply. In wet weather my backend is all over the road. This happens whenever I take off from traffic lights, and when I turn corners.

It is not just that I am a bad driver (I hope) I am only going to 1500 revs to take off, as I am particularly careful in wet weather.

Could anyone give me some tips to stop this, and I wanted to know if a good set of tyres would help at all. The tyres on it are only six months old, so I wondered if I could just get good tyres for the back. If it will stop my backend from sliding, I would be happy to spend up to $300 per tyre (only for the back).

Link to comment
https://www.sau.com.au/forums/topic/12288-tyres-1994-r33-gts-t/
Share on other sites

angel,

You need some Diff cradle bushes. Whiteline suspension does the kit part number KCA349.

This kit installed in the traction position will give a better chassis transfer of power.

You will find cars that have suspension set too low or hard at the front suffer badly from traction issues also.

As for tyres,

The good old simex brand are fab for the price. Get a 225 or 235/55 for the back ( a fairly tall profile for good sidewall flex at the drags). Don't buy the simex tyres for the front tho' they radial roll too much.

My little 205/55 simex tyres got me a 13.4 second 1/4 so they are not a bad pick.

the kit cost less than $120.

Takes 10 to 20min to install. I did mine by myself with a big iron bar and almost crushed my fingers into jam but, an ordinary two person team can do it with a minimum of fuss and no danger at all.

Bat the eyelids at some of the perth boys to give you a hand, if that doesn't work then offer free beer. Or do both. You might want to make sure that the helpers have done the install before having said that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...