Jump to content
SAU Community

Recommended Posts

motor: rb25det

upgrades: hks gtrs turbo, power fc, 3" turbo back, power FC boost controller, 555cc injectors, tomei poncams, Pod filter

Problem: Whenever i take the car for a cruise... I stomp on it... boost climbs to approximately 10psi and as soon as it reaches 10psi, the boost starts to fade back down to 0 psi.... almost like the wastegate is stuck open.... it will remain at 0 psi until i let off the throttle and/or push in the clutch... then the pressure will rise back to 10psi and leak back to 0

Idea: I've got the correct vacuum line going from the boost solenoid to the waste gate... but the other line on the boost solenoid which is supposed to go to the cold pipe, is hooked up to the metal tubing that runs underneath the charge pipe and leads to the throttle body plate... can't remember if it's the "com" port or the "no" port on the actuator... but i have read that it is supposed to connect to the cold pipe before the throttle body, via a nipple welded onto the cold pipe

Lets hear the ideas/suggestions

Link to comment
https://www.sau.com.au/forums/topic/122931-rb25-wont-hold-boost/
Share on other sites

Did you use that silicone hose to plumb to the actuator? if so, put normal vacuum hose on and try it. Otherwise test actuator with compessed air. could be tear in diaphram.

motor: rb25det

upgrades: hks gtrs turbo, power fc, 3" turbo back, power FC boost controller, 555cc injectors, tomei poncams, Pod filter

Problem: Whenever i take the car for a cruise... I stomp on it... boost climbs to approximately 10psi and as soon as it reaches 10psi, the boost starts to fade back down to 0 psi.... almost like the wastegate is stuck open.... it will remain at 0 psi until i let off the throttle and/or push in the clutch... then the pressure will rise back to 10psi and leak back to 0

Idea: I've got the correct vacuum line going from the boost solenoid to the waste gate... but the other line on the boost solenoid which is supposed to go to the cold pipe, is hooked up to the metal tubing that runs underneath the charge pipe and leads to the throttle body plate... can't remember if it's the "com" port or the "no" port on the actuator... but i have read that it is supposed to connect to the cold pipe before the throttle body, via a nipple welded onto the cold pipe

Lets hear the ideas/suggestions

what bov are you using?

still using the OEM BOV... wondering if i need to adjust the duty cycle on the PFC boost functions?

using OEM vacuum hose... this stuff wouldn't collapse just yet... i really do think it has something to do w/ how i've got the intake charge pipe vacuum line hooked up

Edited by zinkrb250

tested the wastegate... works fine...

Now when the car hits approximately 10psi it cuts off (boost press. drops/engine shuts off) only for a second... then it kicks back on as soon as it drops below 10psi... and it will keep doing this as long as my foot is on the pedal and we're at 10psi of boost...

The car literally feels like it's shutting off - then on - then off - then on...

I've got it checked on the PowerFC option "yes" that i've got the boost controller kit....

I tried turning that off and i boosted up to 15psi before i let off the gas... it didn't do any of the on/off/on/off stuff...

So what does this tell me?

the map sensor is T'd off of the vacuum line going to my Fuel press. reg.... it reads boost fine on my hand controller...

I was missing the factory boost solenoid and harness when i installed the rb25 into my s14 so i had to hardwire a 12v. source to the AFM 12v source... then i ran the earth wire from the apexi solenoid to pin 25 on the efi harness.... according the the rb25 wire schematics, pin 25 is the boost solenoid control...

I can hear the apexi solenoid click whenever i turn the ignition to "on"...

I get a 12v reading whenever i check for power on the apexi solenoid

So its setup like in the diagram.

post-12828-1151529964.jpg

Correct... The wastegate vacuum is running to the "COM" port (short length of hose as recommended in the instructions)

but i don't have a nipple on my intercooler piping (it's the FMIC Hybrid kit)... so instead of having the "NO" port vacuum line running before the throttle body, it's attatched to the throttle body plate that attatches to the intake plenum...

here's a picture of what i'm talking about.... This is and old one before i installed the apexi solenoid but it'll still give you the right impression....

The vacuum circled in the picture is where i've got the "NO" vacuum line plumbed....

e6fd5f70copy.jpg

according to the apexi instructions it should be before your throttle body on the cold side of the intercooler piping

Correct... The wastegate vacuum is running to the "COM" port (short length of hose as recommended in the instructions)

but i don't have a nipple on my intercooler piping (it's the FMIC Hybrid kit)... so instead of having the "NO" port vacuum line running before the throttle body, it's attatched to the throttle body plate that attatches to the intake plenum...

here's a picture of what i'm talking about.... This is and old one before i installed the apexi solenoid but it'll still give you the right impression....

The vacuum circled in the picture is where i've got the "NO" vacuum line plumbed....

e6fd5f70copy.jpg

according to the apexi instructions it should be before your throttle body on the cold side of the intercooler piping

Cant remember if you can get the duty cycle reading on the hand controller but see if you can get a multimeter that measures it. Then you will be able to see if you have a mechanical problem or an electrical problem.

Yes.. On the H/C under settings - boost - you have about 5 different boost settings to choose from.... next to each boost setting you've got the duty cycle setting and then next to each duty cycle setting is the number 255...

right now i've just got it on the lowest setting of .5 mmhg? and then 48 duty cycle....

These were the original numbers already in the pfc from apexi

Wouldn't i have to be driving the car to use the multimeter to see when or if the solenoid was opening?

umm if its after then that might be your problem, you want it before the butterfly plate so its on the charge pipe side...not the plenum side. As typically you would have it off the turbo charger housing or somewhere around there on your intercooler piping. I believe that for quickest response you try and set it at a point closest to the pressure source...which is your compressor outlet.

Yes.. On the H/C under settings - boost - you have about 5 different boost settings to choose from.... next to each boost setting you've got the duty cycle setting and then next to each duty cycle setting is the number 255...

right now i've just got it on the lowest setting of .5 mmhg? and then 48 duty cycle....

These were the original numbers already in the pfc from apexi

Wouldn't i have to be driving the car to use the multimeter to see when or if the solenoid was opening?

Yes thats right there are four boost setting each with a boost pressure set level and a starting duty cycle. The way it works is you take a stab at the base duty cycle from here the PFC works out wether or not it is above or below the boost set point and decides if it needs to increase or decrease the duty cycle to achieve the desired boost level, it does this throughout the entire rev range at a frequency of about 40Hz from memory. That means it can calculate a duty cycle 40 times per second.

Now what happens if you set a high base duty cycle and a low boost setting is it spikes up using the base duty cycle guess and then it sees that its current boost point is too high for the desired boost level and it pulls the boost out by reducing the duty cycle. Remeber it can only go as low as the base wastegate spring pressure if it is less than this at any point the you have a mechanical problem. A good test would be to take the boost solenoid out of the equation and see if it holds wastegate pressure.

The setting you have in there of 0.5kg/cm2 = about 7psi which is probably pretty close to wastegate spring pressure. So if your duty cycle of 48 is spiking to say 15 psi and you are trying to run 15 pound then you need to put in a boost setting of 1.05kg/cm2 = 15psi.

Edited by rob82
Yes thats right there are four boost setting each with a boost pressure set level and a starting duty cycle. The way it works is you take a stab at the base duty cycle from here the PFC works out wether or not it is above or below the boost set point and decides if it needs to increase or decrease the duty cycle to achieve the desired boost level, it does this throughout the entire rev range at a frequency of about 40Hz from memory. That means it can calculate a duty cycle 40 times per second.

Now what happens if you set a high base duty cycle and a low boost setting is it spikes up using the base duty cycle guess and then it sees that its current boost point is too high for the desired boost level and it pulls the boost out by reducing the duty cycle. Remeber it can only go as low as the base wastegate spring pressure if it is less than this at any point the you have a mechanical problem. A good test would be to take the boost solenoid out of the equation and see if it holds wastegate pressure.

The setting you have in there of 0.5kg/cm2 = about 7psi which is probably pretty close to wastegate spring pressure. So if your duty cycle of 48 is spiking to say 15 psi and you are trying to run 15 pound then you need to put in a boost setting of 1.05kg/cm2 = 15psi.

Well i took the solenoid out of the equation and it held a steady 10-11psi ....

So does this mean (on the pfc h/c) that on boost setting #1 at .5kg/cm2 i should lower duty cycle from (factory) 48 to....?????? what? I have no idea how this thing works

Well i took the solenoid out of the equation and it held a steady 10-11psi ....

So does this mean (on the pfc h/c) that on boost setting #1 at .5kg/cm2 i should lower duty cycle from (factory) 48 to....?????? what? I have no idea how this thing works

So that means that you have a 10psi actuator.

If you want to run 15psi then put in 1.05kg/cm2 for boost and try about 50% duty cycle. If the boost shoots over 15psi but then drops back down high in the rev range reduce your duty cycle by 5% then try again. Do this for each boost level you desire remeber the high the boost level the more base duty cycle it will need and vice versa for less boost.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...