Jump to content
SAU Community

Recommended Posts

Hi all,

After reading most of your nice advices about the 4wd check light problems in the gtr32s to help to solve mine (gtr34 v-spec), unlucky nothing seems nere. Here is the problem that I've been noticing:

Usuallly, when it's cool (ambient temperature/left overnight), it ocurred less often. Sometimes, just started the engine for awhile, the 4WD and A-LSD check light came on at the same time either on stationay (while idling) or rolling on a constant speed. Tried to turn the engine off/on, the check lights went off and came back on after awhile. How come, these two check lights came on together??

I've checked the fuses in the egine bay + driver's kick panel, fluid level, the relay to the fluid pump motor. They are all fine. One thing I haven't checked is the pump motor cause I wasn't sure how to.

I had an advice that, have a ATTESA computer diagnostic test, but I'd love to sort the problem out with your advices if it's possible before bring the car to a mechanic.

So please advice me how to solve this problem, THANKS GUYS !!!

well I've not had a look at the 34 computer, have a look at it (in the boot under the parcel shelf). when the 4wd light is on there will be an LED flashign a code number. Check the code number to the list of error messages in the 32 GTR workshop manual.

All on the assumption it works the same as a 32, my guess is the computer will still show error codes to help with problems like this.

All the other solutions like fluid, bleeding etc won't really help if the 4wd light is on. Most likely cause is a poor earth / bad voltage somewhere for intermittent problems like this.

Thanks Duncan,

I think you're right about the wirings. Yesterday, when it was in good condition, I tried to shake the wire loom near the pump => the check light poped up => turn off the engine => shake again => turn on => check light was gone. So, very high chance it's somewhere there. I'll strip it down on the weekend and I'll update to you later.

Cheers!!!

Hey guys !!

I've found where the intermittant bastard is !!! The water and corrosion contaminated on the connector of the fluid pump side. The voltage got leaked and shorted intermittantly caused the 4wd and

a-lsd check light came up. Just disassemble the connectors to clean the corrosion => DONE => THE GOZILLA IS HEALTHY AGAIN !!!

CHEERS!!!

  • 3 years later...
Hey guys !!

I've found where the intermittant bastard is !!! The water and corrosion contaminated on the connector of the fluid pump side. The voltage got leaked and shorted intermittantly caused the 4wd and

a-lsd check light came up. Just disassemble the connectors to clean the corrosion => DONE => THE GOZILLA IS HEALTHY AGAIN !!!

CHEERS!!!

Hi mate I got a same problem as you. can you point out where is the connector??? front?? in the boot??

you don't really want to know....there are orange and grey connectors on top of the attessa pump. which is on top of the diff. don't think you will have much luck getting to it without dropping the subframe.

you don't really want to know....there are orange and grey connectors on top of the attessa pump. which is on top of the diff. don't think you will have much luck getting to it without dropping the subframe.

thanks mate, so how long it will take if let workshop do it?

you don't really want to know....there are orange and grey connectors on top of the attessa pump. which is on top of the diff. don't think you will have much luck getting to it without dropping the subframe.

I found the pump is just under the right rear of the car i clean and replug it. the light not come up for 15kms so far. so maybe fixed.

sorry not sure how long it would take a workshop with a hoist.....would take me an hour to drop the subframe and 1/2 to raise it again but that has been on and off a few times.

definately a job to get someone else to do :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...