Jump to content
SAU Community

Jackets... Get Your Supercool Sau Vic Jackets...


Recommended Posts

  • Replies 279
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Is that because you put your jacket down somewhere and swapped it with someone elses?

Na Bec

I noticed i had a XL a couple of nights after i picked it up from the meeting. And that night i took it straight out to the car..

All is good im happy with it .. But if someone wants to change a M for a XL thats cool to..

Am still waiting on payment for the following jackets:

Daz (spdkls) 160.00 Need response

Skybee (Ben) 160.00 Still wants it - will pick up soon

Crack (craig) 120.00 Need response

Yug 120.00 Need response

Mike Lowry 120.00 (to pick up/pay for at September meeting)

acsplit (Andrew) 120.00 Still wants it - will pick up soon

buzzin (Luke) 120.00 Still wants it - will pick up soon

coupethis 160.00 Need response

Graeme (gdogzgtr) 120.00 Still wants it - will pick up soon

For those of you who have indicated that you still want your jackets, if you could PM when you are ready to collect/pay, etc.

For the 3 people I have not had a response from, if I still have not heard from you by the end of next week your jackets will be sold if someone else is willing to pay before I hear from you.

I also have 2 M and 1 XXL left if anyone is interested.

Cheers

Hey Bec, I would be interested in one, but I'm intending to become a member some time soon so I guess i may aswell wait til then and save myself $40.I think I would be after a medium. Hopefully you might have one left!

Ok, sorry about the delay, but I'm cashed up now. I got the bank to put my member # as reference.

Pick the jacket up next meeting if that's ok?

Thanks.

Yep - got your payment. Thanks.

Pick-up at the meeting on Tuesday will be fine.

See you there.

  • 4 months later...

OK - after selling a couple more jackets over the weekend I have done a stocktake and the below is what I have left:

MEDIUM - 3

LARGE - 1

XX LARGE - 1

Prices are $120 (members) or $160 (non members).

I also have one XL jacket only (ie no vest) which if someone wants they can have for $80 (members) and $100 (non members).

Some of the above jackets have been reserved by the following

Daz

Skybee

gdogzgtr

(if you guys are still interested, PM me ASAP).

But - jackets are now on a 'first to pay, gets it' system.

So.........anyone interested, post here or PM me :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...