Jump to content
SAU Community

Recommended Posts

I have done a fair amount of research,read the FAQs sticky on here,and the relevant government agency sites and can't quite come up with an answer.

Heres the story..I bought a 1990 R32 GTR track car (thats not registered in my country and can't be)and had intentions to further modify it and use it as a weekend track car.

However my situation has changed and I have plans to move to aussie to work (hard work to modify the GTR as much as possible) as the lifestyle and weather is more to my liking.However I can't seem to find how id be able to import the gtr.

Anyone got any ideas or I might have to leave the car behind:(

i've found this section appealing but can't quite understand it.I've owned the car only 7months now.

"Vehicles built before 1 January 1989 may be imported to Australia without restriction. An import approval is still required and the enclosed application from should be used.

"The vehicle must be built prior to 1 January 1989 unless it meets the transitional arrangement below:

If you made a financial commitment and purchased a 1989 or 1990 vehicle prior to 7 February 2005 you may apply to import your vehicle until 31 December 2005; but

If the vehicle is a 1990 year of manufacture you may only apply on or after the month when the vehicle turns 15 years old, eg a vehicle manufactured in September 1990 can be applied for import in September 2005 provided there was a financial commitment before 7 February 2005. "

Any help would be appreciated.

Link to comment
https://www.sau.com.au/forums/topic/124466-difficult-situation/
Share on other sites

OK its pretty easy.

1988 and older cars can be imported to Aus without much restriction, they just need to be signed off by an engineer as safe when it gets here. That rule will probably change in 2020 to include 1990 cars if you want to wait until then.

Race or Rally import can be done by someone with a CAMS motorsport license, race import can never be registered in Aus, Rally import can get "conditional registration" which allows it to be driven to and in events and practive

SEVS allows full road rego of certain cars (if compliance plates exist). Compliance typically costs 3k to 6k and only certain models and dates of cars are available. Cars must be totally stock right down to factory brake pads.

The last option is private import, if you can prove you have owned a car overseas for at least 12 months you can import it and register it. Otherwise same rules as 15yo rule.

If you can prove you have owned the car for 12 months private import is the way to go for sure

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...