Jump to content
SAU Community

Recommended Posts

:wub: Hey everyone

Im looking for anyone who supplies the D-MAX Wide body over fenders for r32 skyline , Iv seen them on there Japanese site but it only says r32 Im assumming its for a r32 gts skyline,im wanting them for my r32 gtr,I need to know if the kits they supply are for a gtr and are the guards (mainly the rears) more pumped than the standard factory guards?Any pics with the kits on r32 gtr would also be great.:dry: thanks alot

Link to comment
https://www.sau.com.au/forums/topic/125114-d-max-fenders/
Share on other sites

They're not specifically for GT-Rs, although theres not much stopping you from putting them on a GT-R... if you wanna go down that route.

The D-Max rear fenders are probably a tad wider than stock GT-R rears, but you'd be spending alot of cash for minimal gain I'm pretty sure. You must have a serious set of wheels to be wanting to go wider with a GT-R.

The front fenders are probably a straight fit, although I'm not sure about the front indicators, you might need to run HCR32 ones.

D-max are the dogs danglies, I've got one of their carbon bonnets :wub:

Link to comment
https://www.sau.com.au/forums/topic/125114-d-max-fenders/#findComment-2310520
Share on other sites

They're not specifically for GT-Rs, although theres not much stopping you from putting them on a GT-R... if you wanna go down that route.

The D-Max rear fenders are probably a tad wider than stock GT-R rears, but you'd be spending alot of cash for minimal gain I'm pretty sure. You must have a serious set of wheels to be wanting to go wider with a GT-R.

The front fenders are probably a straight fit, although I'm not sure about the front indicators, you might need to run HCR32 ones.

D-max are the dogs danglies, I've got one of their carbon bonnets :wub:

:dry: Cheers Rezz , Im after the Group A (Japan) look , Iv already a du luck body kit now just want to inhance the guards some more with out ruining the lines of the car. Do you know of any other companys like this?or a D-MAX supplier in Aussie?

like this BeeR fender kit but its not made anymore :P

post-13835-1152179618.jpg

Link to comment
https://www.sau.com.au/forums/topic/125114-d-max-fenders/#findComment-2310568
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...